วีดีโอ

Nice video, thanks. I've had to start some POS cars I had with a screwdriver, back in the day. I luv it when manufacturers put service parts in the most pain-in-the-butt places.

Excellent tutorial video. I've been delaying this task till you have made it crystal clear. Thanks.

Im getting no clicks at all it makes no sound of it trying to crank all the lights and horn works but no sound at all trying to crank

Where you order those wires from?

About to do the same thing with 6x8 Kickers.

Helped me out with my 21 year old Expedition today. Thank you for the assist in 2024!

You rock my man. I changed my starter. Checked my battery. Checked my relays. Nothing. Seen your video and yanked and twisted my positive cable and presto this man is a life saver. Thanks a million

Thak you for your calm and easy paced instructions. Not above my head for someone who knows nothing about mowers.

Thank you, my port fell down because the plastic thingamajigger is broken and I was stressing because I didn't know how long it would take to get it out.

Where does your negative ground wire go to from the starter to the top ...where it leads too?

When I try to start my the starter makes a hissing sound almost like it’s stuck

Oh man i have that same grip but the AK version on my m92. I love it! I just put a hogue sleave on my factory ep9 handle

I'm getting it to turn over even when the key is not in the on position. Any idea what that means?

Thanks for the video, Bro! God bless…

I have a 06 electraglide and this video was exactly what I've been looking for. Thank you

Hi there Guys, So I just did the 24V "upgrade" using the Anti GRavity 801 and 401, and everything works very well, however it seems like I burn the starter motor real quick, how do you guys get around this challenge.

You really shouldn't be making videos pal.

Can you show some of the big wire connectors under the console. Somehow I have an extra that am not sure

Very nice, thanks!

I hit mine with a hair dryer, low heat 5 years later, mine are still on and look great!

Spot on. My problem WAS the negative cable. Replace battery post terminal. So make sure the smaller black wire that runs from the negative post to the truck frame has enough bare wire so it will ground properly. Thanks again.

man I was gønna ask you if I could swap a center console with a heated seat addition untill I noticed your buttons are on the climate control, I guess yours is 05+? I got a 03

Thanks man...been struggling with my dads mower. Which almost the same as yours. Itll fire but i crossed wires somewhere..thus helps but i still have to investigate.

Thank’s body, it was really hepfull!

Thank you

Much Mahalo for your vid. Diy install amateur radio amp to driver side console. Aloha from Hawaii.

Great video..I’m late to watch it helped me out with my case I purchased 3 days ago. Thank you

Thx 🤝

Dude that lil Boston is so precious

I'm a professional parts installer too.

Well done video Greg. I like that you put the pistols in vertically rather than flat, better utilization of the deep case. I may copy your idea.

Where did you get the light, what brand was it?

Great video

The terminals are still very corroded. I wonder if you cleaned them it would have corrected it.

Bro I got the truck same problem!! Thanks for the video you probably just saved me a lot of time and $$. Good looking out

IF YOU NOTICE THE WIRE COLORS ARE RED BLACK AND VIOLET. THE GOLD STRIPE ON 1ST THE RESISTOR GOES TO THE RED WIRE. THE TOP GOES TO THE MIDDLE BLACK WIRE. THEN THE GOLD STRIPE ON THE 2ND RESISTOR GOES FROM MIDDLE BLACK WIRE WITH THE TOP GOING TO THE THE VIOLET WIRE. Epoxy Baby! CURES EVERYTHING DUCT TAPE AND ELECTRICAL TAPE CAN'T.

That puppy dog wants a resister and get his kick stand bypassed. Don't you warm up your bike on your kickstand? I do!

Probably would have figured it out ....... Eventually. Nice to have someone Show what I need to do before hand! Thanks!

I've got the same issue. Great video!

You have some nice guns dude!

This was very helpful brother.

Mine’s is 2006 xlt my mirrors don’t have a puddle lamp can I add them or I need to change the hall mirror and some Wiring to make it work any one know plz?

Correction: what I did was to drill the thread hole a bit larger and inserted a bolt from behind and then apply a pressure washer and a wing nut.

Could you use a bolt and pressure washer and nut, inserting the bolt thru the front.

Same problem....thanks GP!

Bought mine on Wednesday 24th, got it 2 days later. I live in AZ so got it real fast.

Perfect explanation, helped me a lot THANKSSSSSS

Servicing the power ports. Changing them to USB for phones, etc. Great help thanks!

Brothank you so much God bless

NEXT FORD will be riveting the rims and tires on, what a joke ford, bet your setting back and laughing at people trying to fix what should be simple repairs!