- 9
- 498 157
iAuto Tech
United Kingdom
เข้าร่วมเมื่อ 25 ธ.ค. 2020
Seat Ibiza Front Brakes Replacement
How to replace front discs and pads on a Seat Ibiza 2012.
มุมมอง: 385
วีดีโอ
How To Replace A Front Coil Spring on a Seat Ibiza 2012
มุมมอง 7K8 หลายเดือนก่อน
Seat Ibiza front coil spring replacement. I would have preferred to remove the complete hub but I didn’t have the tools so had to do without.
Timing Chain Replacement VW Golf TSI 1.4
มุมมอง 469Kปีที่แล้ว
Had a rattle sound from the timing chain when starting the car. Timing chain was stretched as shown in the video.
👍👍👍.
This is just so beautiful 😍
Don't take chance to do at your you end up worsenig the fault.
Perfect uitgevoerd en in volgorde. 👍👍
Where are you based? I need mine done
guys after how many km should a timing kid be changed?
120k km or something depends tsi engines 2009 till 2012 maby efter 60k km depends if you do al your services
thx for the video very educational! what do you think can someone with zero experience do this following your guide step by step? I put some machines together but I never done cars before. Would be nice if I could do my own maintenance and save some big bucks.
What was the mileage on the car. Excellent vid thanks
Thank you. Mileage was around 50k
Good work 👍
Kein Kühlwasser aufgefüllt😂😂😂
why were timing chains introduced if they too have to be replaced like timing belts? with belts it was better as there was an interval on which they ought to be changed.
Well older chains one rearly had to change,mostly the newer models were they gotta have alot of "tek" that can fail
Absolutely fantastic video. I've a question I hope you can help with. My 1.4TSI [CAXA] engine has thrown a P0016 fault code three times in three days - I cleared it each time. Could this be anything other than the timing being out ? Do I need to get a timing chain kit and bite the bullet ? Thanks in advance for all help/advice.
not a professional but from my research so far I saw someone changing the a timing chain for the same engine and that error was popping up and the mechanic in the video said its a timing chain error. but take this with a grain of salt of course
@@filipadamczewski2571 Just to update... a couple of weeks ago I decided to strip the engine to discover the timing chain had stretched around 2cm ! So to answer my own question - No ! And your mechanic was correct :)
My touran 2008. 1.4 tsi. Is running not great and putting fuel in threw oil could this be the timming off
How do you assemble the strut again. I’ve unassembled but forgotten how to put back. I’ve got metal housing for sping. Big rubber circle and small rubber circle. What goes first if you don’t mind helping me
Check video from 5:23
ciao vorrei sapere perche il comparatore e messo non a zero e poi non si legge a quanti gradi e messo grazie
It doesn’t need to be set at zero, it’s just a guide to show TDC
@@iAutoTech cosa sarebbe il TDC?
@@ziupeppuwhen the pistons at the top on cylinder 1
Nice job
I’m confused I have the exact same engine replaced the timing chain and it still makes the same noise
I have a VW touran 1.4 tsi cvac engine which rumbles on start, on 114 k miles, i may need chain and associated parts changed very soon. Would you be open to doing it? Im based in Bham, if not who could you point me to?
Sorry I’m not taking on any work at the moment. Just try your local garage.
@iAutoTech won't be doing that. I had a golf same engine twincharged in 2017, took it to a local mechanic for similar work and the crankshaft pulley fell off while driving some while later. Wrecked the car. Will just look for a reputable place. How much do you think I should be charged for whole chain kit replacement including labour, ball park?
@@hnc9costs wise it depends on the garage labour rate per hour. This job will take no more then 6hours and this timing chain kit was £300.
Very nice, thank you! Please what parts did you use? OEM, FAI, Hepu? I have a 2005 1.4 FSI AXU 60k miles. It rattles at cold start 2 3 seconds, if is stays for a couple of days. I switched to 5w40 from 5w30 but it still does. Please do you have a link for how the comparator clock works? I don t get it why you have to use it twice.
Thanks for the feedback. I used FAI timing kit. Oil thickness wouldn’t really make a difference to a stretched chain. Comparator?
Thank you! Comparator clock =the tool that you put on cilinder one instead of the sparkplug.
@@cartaginalandscape6349sorry don’t have a link.. it just shows piston at TDC.
Thanks! Please, i have a couple of questions. May I write it here or you have an e-mail adress? I'm not from U.K. I don't want to polute here(don't know the youtube policy) or bother you.
@@cartaginalandscape6349 no probs just write it here
Do i have a bad tensionner in my picture please help thank you
Sorry can’t tel by looking at the image
C’est un super travail J’ai une question, le moteur est toujours un peu brouillant ? Surtout à froid, c’est normal ? Ça claque beaucoup ce moteur ? Merci
Thank You. It use to rattle sometimes on start up and after the timing chain was done it’s been ok.
Best video Meilleure video Bravo
Pourquoi ?
Is it possible to do this without a dial gauge? Using only the cam lock & crank tool
Yes you can use a screwdriver to check the piston is at TDC
@iAutoTech thank you last question; to get tdc, should the crank hit the locking bolt 🔩 when you rotate clockwise, or you get tdc before the crank hits the locking bolt 🔩?
@@luckympho_mShould get TDC when the crank tool hits. I would Add a gauge/screwdriver just so I know it’s at TDC.
@iAutoTech did the same process twice. At first, i thought my timing wasn't ryt then re-did the timing, but the car still cranks only no start
HOW MANY HOURS DID YOU DO IT? FRIEND!
Think it was about 5hours
Will change it after 13 Years too ✌🏻
Hi where are you based so i can get this done please
Sorry I’m not taking any work on at the moment
You make it look so easy. It took me 10 times longer. Many thanks for posting.
Thank you for the great video, it is helping alot.. however I have a question about the chain you changed in the engine does it cause the (EPC) light to turn on in the car tableu? Thanks in advance!
Thank you for the great video, it is helping alot.. however I have a question about the chain you changed in the engine does it cause the (EPC) light to turn on in the car tableu? Thanks in advance!
Thank you. Yes it can do if the timings out and the vehicle goes into limp mode.
Wonderful content! Thanks for sharing. Just subscribed and liked!
Thank you for the feedback 🙏🏽
I would not touch it either. You need to know exactly what you are doing and have the right tools. Besides.... I am in ny 70'ties, retired and tired working on cars. 😊
mahtava video. tällä videolla pystyy hoitamaan ketjun vaihdon
Hi mate, is it possible to reach for some questions before I srart this?
Yeah sure
I have an Volkswagen touran 1.4 tsi and i was at dealer to ask if they can change the chain ,but they told me that is not needed to do it never . I ask another one and they told me the same , they said on this model is not necesary to change the chain . And the 3rd one ask me 2700€ to do it but they said also is not necesary to do that because this chain is made to work entire life of the car . Something is strange
Are you having any issues with it?
Great video. Nice angles and clear image. What did you torque the cam bolts to? I didnt see that? Cheers
Thanks for the feedback This info I got from Haynes manual for cam torques Tighten the inlet camshaft (40Nm) Tighten the exhaust (50Nm) Then check timing and if the timing is correct then tighten (90°) for both pulleys.
Hi brill video pal ive started mine going through the steps shown by you so you have made it a lot easier i have a streched chain it is sloppy on top so its jumped on the cams as the end cam tool pins do not line up so how do i go about getting them back into line without the cams springing round on me ? Thanks in advance
Thanks mate.. have you tried to take the sloppiness out by turning back the cams? (from cam bolts) If you can get the tool into place with slight pressure pushing it in and get one cam to line up, then turn the other cam slightly so you can insert the tool fully into place. Hope this helps.
bravissimo hai dimenticato una fascetta
Alguien sabe dónde comprar el kit para bloquear los árboles de levas el cigüeñas y el tensor de la cadena?
Have a look on Amazon or eBay, got mine from ebay
very helpful video bud, how long did this roughly take
Thank you. It took around 5hours to do.
Återigen en modern fröken m gummihandskar som är rädd bli skitig.
Thanks for letting me know that to be a man you need to have dirty hands. 👏🏽
Timing chain u don't speak how to timing the chain and marking
It’s all shown in the video. What do you need to know?
And without adverts! Nice job! Extremely helpful video.
Thanks for the feedback
Just take it out and do a "dukes of hazard" jump, it'll hold
Mint! 👌
Mudo
Thanks for the video. And which step did you tighten the camshaft bolts to the camshaft gears? Was it while the crankshaft locking bolt and camshaft holding tool was still in and the chain tensioner pin had been pulled? Cheers
Hi the steps I followed was make sure timing tools are in place , install new chain and pull the tensioner pin and then slightly tighten the bolts (cam) while timing tools are in place and then turn engine to check timing. If timing marks all line up after x2 turns (put timing tools back in place) then tighten bolts to the correct torque settings. Hope that helps
@@iAutoTech amazing thank you.
can you write if you need any special tools on tight bolts on camshafts, thx for answer@@iAutoTech
@@diagnostikacartruck1398 you can get a tool to hold the cam sprockets while you tighten the bolts but I used drill bits and a screw driver which I wouldn’t recommend.
thank you
Hi, great tutorial video. Used for my chain replacement a month ago. What is this black box at 1:51 ? I dont unplug hose/cable for this. I just take off attachment bolt and moved away. My 1.4 tsi engine runs fine atm and new chain didn't make noises during the start anymore. Thanks for the video! Ps. I recommend to buy cheap moment tool for example crank shaft pulley. Making pulley holder tool by self is quit easy as well.
Hi, thanks for the feed back and Im glad the video helped. The black box your your referring to is a EVAP charcoal canister.
Tiene q modernizar todos esos vejatorio q tiene
Was ist mit dem Zahnrad auf der Kurbelwelle ? Hat das kein Verschleiß?