- 70
- 954 510
KEY TECHNIQUES
เข้าร่วมเมื่อ 2 ธ.ค. 2013
Welcome to KEY TECHNIQUES.
You will be provided with clear, simple and easy to follow Technical Drawing videos on the basic drawing principles used in Technical, Mechanical or Engineering Drawing.
Key Techniques was created as I sought a way to teach students who were learning Technical Drawing for the first time during the covid¹⁹ pandemic. Students were unable to attend face-to-face classes but were not at a disadvantage to learn Technical Drawing which is a very practical subject. These videos are sure to provide basic Technical Drawing demonstration for beginners of the subject in mind.
Feel free to share the videos with those you think will learn from this channel.
You will be provided with clear, simple and easy to follow Technical Drawing videos on the basic drawing principles used in Technical, Mechanical or Engineering Drawing.
Key Techniques was created as I sought a way to teach students who were learning Technical Drawing for the first time during the covid¹⁹ pandemic. Students were unable to attend face-to-face classes but were not at a disadvantage to learn Technical Drawing which is a very practical subject. These videos are sure to provide basic Technical Drawing demonstration for beginners of the subject in mind.
Feel free to share the videos with those you think will learn from this channel.
How to draw ISOMETRIC PROJECTIONS | Technical Drawing | Exercise 12
Learn to draw isometric projections using these simple steps provided. Isometric drawings are easy once you learn the basic Techniques.
มุมมอง: 122 867
วีดีโอ
Draw an Isometric Projection | Technical Drawing | Exercise 11
มุมมอง 6K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an ISOMETRIC DRAWING. This video is the 11 th of this series.
Draw an Isometric Projection | Technical Drawing | Exercise 10
มุมมอง 6K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an ISOMETRIC DRAWING. This video is the 10th of this series.
Draw an Isometric Projection | Technical Drawing | Exercise 9
มุมมอง 2.8K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an ISOMETRIC PROJECTION. This video is the 9th of this series.
Draw an Isometric Projection | Technical Drawing | Exercise 8
มุมมอง 3K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an ISOMETRIC PROJECTION. This video is the 8th of this series.
Draw an Isometric Projection | Technical Drawing | Exercise 7
มุมมอง 4.1K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an isometric projection. This video is the 7th of this series.
Draw an Isometric Projection | Technical Drawing | Exercise 6
มุมมอง 3.4K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an isometric projection. This video is the 6th of this series.
How to Blend ARCS and CIRCLES | External Arcs
มุมมอง 23K3 ปีที่แล้ว
Learn to BLEND EXTERNAL ARCS to two given circles ( radius 30mm and radius 20mm respectively)
How to Blend ARCS and CIRCLES | Internal Arcs
มุมมอง 66K3 ปีที่แล้ว
Learn to BLEND INTERNAL ARCS to two given circles ( radius 30mm and radius 20mm respectively)
How to draw an Isometric Projection | Exercise 5 |Beginners
มุมมอง 193K3 ปีที่แล้ว
This ISOMETRIC PROJECTION video lesson will demonstrate simple steps you use to draw an isometric projection. This video is the 5th of this series.
How to draw an Isometric Projection | Exercise 4
มุมมอง 4.3K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an isometric projection. This video is the 4th of this series.
How to draw an Isometric Projection | Technical Drawing | Exercise 3
มุมมอง 5K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an isometric projection. This video is the 3rd in this series.
How to draw an Isometric Projection | Isometric Rectangle | Exercise 2
มุมมอง 26K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an isometric projection. This video is the 2nd in this series.
How to draw an Isometric Projection | Isometric Square | Exercise 1
มุมมอง 31K3 ปีที่แล้ว
In this video, I will demonstrate the steps you use to draw an isometric projection. This video is the 1st of a series of 12.
How to REDUCE and ENLARGE a quadrilateral | Radial Method | Technical Drawing
มุมมอง 9K3 ปีที่แล้ว
In this video, I will demonstrate step by step how to REDUCE and ENLARGE a Plane Figure. In this lesson, a quadrilateral will be reduced and enlarged RADIALLY . This is the second Direct Method.
How to draw an Irregular POLYGON | Pentagon | Technical Drawing
มุมมอง 9K3 ปีที่แล้ว
How to draw an Irregular POLYGON | Pentagon | Technical Drawing
Construct an Irregular Polygon | Irregular Pentagon
มุมมอง 3.7K3 ปีที่แล้ว
Construct an Irregular Polygon | Irregular Pentagon
Construct Irregular Pentagon | Irregular Polygons | Technical Drawing
มุมมอง 14K3 ปีที่แล้ว
Construct Irregular Pentagon | Irregular Polygons | Technical Drawing
Technical Drawing | Reduction and Enlargement of Plane Figures | Direct Method 2
มุมมอง 5K3 ปีที่แล้ว
Technical Drawing | Reduction and Enlargement of Plane Figures | Direct Method 2
Technical Drawing | Reduction and Enlargement of Plane Figures | Direct Method
มุมมอง 24K3 ปีที่แล้ว
Technical Drawing | Reduction and Enlargement of Plane Figures | Direct Method
How to Draw a CIRCLE to pass throught a point and touch a straight line TANGENTIALLY
มุมมอง 8K3 ปีที่แล้ว
How to Draw a CIRCLE to pass throught a point and touch a straight line TANGENTIALLY
Draw a TRIANGLE equal in AREA to a given CIRCLE
มุมมอง 1.5K3 ปีที่แล้ว
Draw a TRIANGLE equal in AREA to a given CIRCLE
HOW TO CONSTRUCT AN OCTAGON GIVEN LENGTH OF ONE SIDE
มุมมอง 2913 ปีที่แล้ว
HOW TO CONSTRUCT AN OCTAGON GIVEN LENGTH OF ONE SIDE
Draw a RECTANGLE equal in AREA to a SQUARE
มุมมอง 6K3 ปีที่แล้ว
Draw a RECTANGLE equal in AREA to a SQUARE
TRIANGLE equal in AREA to a given RECTANGLE
มุมมอง 11K3 ปีที่แล้ว
TRIANGLE equal in AREA to a given RECTANGLE
SQUARE equal in area to a given RECTANGLE
มุมมอง 14K3 ปีที่แล้ว
SQUARE equal in area to a given RECTANGLE
EXTERNAL TANGENT to two UNEQUAL CIRCLES
มุมมอง 20K3 ปีที่แล้ว
EXTERNAL TANGENT to two UNEQUAL CIRCLES
INTERNAL TANGENT to two UNEQUAL CIRCLES
มุมมอง 16K3 ปีที่แล้ว
INTERNAL TANGENT to two UNEQUAL CIRCLES
bet
I❤ This video
How to draw the same dimension using different sides as base
I keep on making the lines crooked, how can I limit it? Also which tools should I use
@@dragonhunter4446 You need to revisit the basics. Tools need for accuracy for this lesson: T square, Set square and a square drawing board/table.
@@KEYTECHNIQUES thank tou
Thanks sirr
@@LetitiaCodoganDaniels-g9e You’re welcome.
Clear and understandable
notice that you can use this technique to draw a tengent line of a given point in a curve
so helpfull
So you know what I could do for mutiple sheets? Using 10 sheets of Bristol and 10 sheets of copy paper on a Basswood board angled like 45 degrees Tape might work but the weight of all the sheets would slip. Dont want to use tacks would ruin my board. Thinking if using thick painters tape and hoping for the best
@@manicniceguy2341 the painters tape or a good quality tape should work. Can also try the tape automotive body repair men use.
Thanks
Thanks for lesson🙌🙏👌🏼
Nice
Why do you stop posting videos
@@user-pe9cu4iv6v I'll try to restart soon.
@@KEYTECHNIQUES ok
It is very very good 👍 and the best one ❤️😊👍
@@DorisOrukpe-d9l Thank you.
THIS IS SO HELPFUL!!🎉
@@user-vm4zq6ju4u I’m glad your were assisted by it.
Thank you
Like 👍
😊
@@epicvideos6104 😎
❤
I have exams tomorrow 😭
@RahulGundawy You will do well. Apply rhe techniques you already know
aspiring architect heree! I really like your videos sir, your channel is PERFECT for practicing and you teach very well! Please continue making videos ❤
@AyumiKaye thank you. Soon you'll be drawing building plans.
You are too fast
Great 🥰👍♥️😍😍😍😍😍😍😍😍😍😍😍😍😍🥰😍🤓
@@GloryUdochukwu-q7othanks.
Nice 😊😊😊😊
@@GloryUdochukwu-q7o Thanks.
Good ,thank you .sir
You're welcome.
well explained ......clear and easy to understand
Thank you
Help I my nigga 🇳🇬🇳🇬🇳🇬🇳🇬🇳🇬🇳🇬
Whats help you need?
i am still confused please do another video via this topic...
i am also consudefd
@@JackFrost-ek2jo at what point did you get confused?
how to draw that given length of 4mm
I think your refering to 40mm. It's done using your T-square and set square.
Guys change the speed on your settings change it to 0.5X
U are way too fast....please try to slow down.
But I have a question...,! How for you get point"P"???? I've understood the other ones but this particular point is an issue to me.
Point P is any random point that you will choose.
Hello 👋👋 sir thanks for all your videos Really appreciate 🎉🎉
Greetings. You're welcome.
0:51 Hi what if the don't have the T square? Can i use my normal ruler to draw
Hi. A T-Square is needed.
Well i don't have any
@@peemo224 I hope you can manage to get one soon. If you know a furniture maker, they can make one for you.
I am 14 year old trying to do my project
Well i don't have any one around me
Hi, I wrote the comment on the M account 3 years ago, its been a while since. How are you doing?
All is good. How are you?
We can't even see you are too fast.
Only the beginning of this exercise was sped up. The previous knowledge from exercise 1-4 is repeated in the section of this video and that is the part that is sped up. If you have the time see exercise 1-4 and you're guaranteed to comprehend exercise 5.
It's true
Thanks
You’re welcome
Really helpful❤️ thanks
You're welcome
Thank you
You're welcome
UP FADA
Thank you so much
You're welcome.
Pakashata
Thank you so much May God Almighty bless you 🙏
You're welcome.
Very helpful video🙏🏿.
You're welcome.
Thanks for this ❤❤
You're welcome.
Super sir ❤
🙏
Too fast
The steps for constructing the isometric rectangle is the only section of this video that that was sped up. This is previous knowledge that was done in some previous videos ( exercise 1 and exercise 2 ) where it was done in real time.
Your teaching is too fast.. a beginner can't learn like this 😢
As a beginner this is exercise 12. Surely, you can't start there. Start at exercise 1 and work your way up. If you do this I guarantee 💯% you'll be straight.
Oww well explained thnk u
You're welcome.
How did u get 90
It just GIVEN for the distance between the center of the circles for this question. Another question will have a different dimension.