- 103
- 95 223
Tuna's Mx-6
United States
เข้าร่วมเมื่อ 28 ต.ค. 2011
Mazda Mx-6 Modification Channel.
This car build is from the late 90's and early 2000's era. Inspired from the SuperStreet, Import tuner, Nopi and Fast and Furious styles. This is a hobby car with small projects here and there. I have been modifying this car since 2002. The car can be seen at local car meets and shows in Tennessee. 93% of the build has been from a residential garage. No lifts or special equipment. No sponsors, Non-Profit build.
Also on Instagram @ tunasmx_6 and sites.google.com/site/1994mx6
This car build is from the late 90's and early 2000's era. Inspired from the SuperStreet, Import tuner, Nopi and Fast and Furious styles. This is a hobby car with small projects here and there. I have been modifying this car since 2002. The car can be seen at local car meets and shows in Tennessee. 93% of the build has been from a residential garage. No lifts or special equipment. No sponsors, Non-Profit build.
Also on Instagram @ tunasmx_6 and sites.google.com/site/1994mx6
Cooling Outlets, Temp sensor, and Thermostat
Part 18 of the $40KLDE build is on the cooling outlets and parts. This includes the thermostat, two temperature sensors, pipes, and hose. I do use a silicone hose from from z1 motor sports.
G37 Silicone Hose www.z1motorsports.com
Sensor and thermostat are from rockauto.com
G37 Silicone Hose www.z1motorsports.com
Sensor and thermostat are from rockauto.com
มุมมอง: 125
วีดีโอ
A'PEXi Radiator Caps
มุมมอง 49หลายเดือนก่อน
The discontinued A'PEXI GTSEC Radiator Cap? Are there two different generations of the caps? or is one a fake? Is one of the caps from Apexera or APEXi, what is the difference?
Installing Cylinder Heads, Lifters, Camshafts, and seals
มุมมอง 4162 หลายเดือนก่อน
Part 17 of the $40KLDE engine build. Installing the Cylinder Heads, Lifters, Camshafts, and seals.
Knoxvagas Elite Kustoms Car Show Nov 23 2024
มุมมอง 542 หลายเดือนก่อน
Some footage of the Knoxvegas Elite Kustoms 2nd Annual Car Show. I was entered in the JDM vs Import category.
Auto Meter Cobalt Series Oil Pressure Gauge
มุมมอง 2414 หลายเดือนก่อน
This is a video on the Auto Meter Cobalt Series Oil Pressure Gauge - Unboxing and Installation on my Mazda Mx-6. For my oil sender, I chose to take the reading from the location of the O.E. oil sender. This is particularly important because I am using an external oil filter relocator with long oil lines. I want to obtain the measurement from this point to ensure accuracy. Also I will be running...
DroppedOut 2024 car show
มุมมอง 955 หลายเดือนก่อน
Tuna's Mx-6 at the Dropped Out 2024 car show August 24-25th. Short video
Cylinder Head Valves and Springs install on a Mazda Mx-6 KLDE engine
มุมมอง 2615 หลายเดือนก่อน
For my new cylinder heads, I successfully installed the valves and springs. I noticed in the video that I initially installed one spring upside down; however, I corrected that mistake later. This is part 16 of the $40KLDE engine build.
New KLDE Cylinder Heads and Valve Steam Install
มุมมอง 3006 หลายเดือนก่อน
I am going with new KLDE cylinder heads for my $40KLDE build. I want this motor to be as new as possible. After ordering 3 different cylinder heads(F42Z-6049-L, F42Z-6049-D , and F42Z-6049-F) I think I have a compatible match. I sealed the heads with a coat of paint, a dash of cleaning, and I Installed new valve steam seals for the final touch!
Addressable LED Brake Light Mazda Mx6
มุมมอง 2047 หลายเดือนก่อน
This is a Prototype Chaser Lights, Sequence LEDs and more. We want to experiment as a Coding 2 class with addressable LED's where LED's can be coded. Unfortunately they do not make a clear lens for the 3rd brake light on a Mazda Mx-6 so we experimented with the stock red lens. This project was set up as a F.A.I.L. First Attempt In Learning which was 88% student driven including most decisions. ...
Short History of Tuna's Mx6
มุมมอง 3528 หลายเดือนก่อน
I purchased my Mazda Mx-6 in 2003 to be a simple daily driver, but now it is a show car! So, what happened? This was a budget build project car, with small modifications made each year. Now more than 20 years in, the time and work added up to a highly modified car. Here is the story.
ARC Super Blow Off Valve
มุมมอง 8859 หลายเดือนก่อน
The ARC Super Blow Off Valve is a classic BOV from the Japanese tuner car culture. This is the early style ARC Super Blow Off valve which has a fixed BOV output port (Funnel/Trumpet). I get to try a dual/twin setup with two BOV's. I had a little trouble getting them to open at first, but they both worked in the end.
$40KLDE part 14 Final Bottom End Build
มุมมอง 36511 หลายเดือนก่อน
Finishing up the last parts on the engine block bottom end for the $40KLDE. I got lucky and found a new oil pan for under $20, and a new oil pickup/screen under $30.
KLDE Oil Pumps
มุมมอง 541ปีที่แล้ว
Mazda-Ford KLDE fans: Get ready for the ultimate High-Volume Stage 2 Boundary! It's a one-of-a-kind replacement equipped with the latest and greatest features. This pump will blow your socks off! Hang on, have you considered a classic OE switcheroo with Evergreen? How do they compare to the stock original oil pump?
APEXi Twin Chamber Blow Off Valve
มุมมอง 1.2Kปีที่แล้ว
Listen up, car enthusiasts! Feast your ears on this classic whoooooshing BOV, but wait, it gets better! This little beauty comes with a flashy red ring and three different holes to fine-tune your car's sound. Now that's what we call mid early 2000's sounds to our ears! It is also known for it's dynamic Duo-Chamber Blow Off Valve, a game-changing, custom-fit device designed for a plethora of use...
K.A. Injection Forged Rods & Pistons($40KLDE Pt. 10)
มุมมอง 840ปีที่แล้ว
K.A. Injection Forged Rods & Pistons($40KLDE Pt. 10)
Jeep XJ Performance Radiator in a Mazda Mx6
มุมมอง 379ปีที่แล้ว
Jeep XJ Performance Radiator in a Mazda Mx6
Gates Water Pump for my KLDE build part 10
มุมมอง 100ปีที่แล้ว
Gates Water Pump for my KLDE build part 10
Cylinder Block Assembly First Steps KLDE engine
มุมมอง 657ปีที่แล้ว
Cylinder Block Assembly First Steps KLDE engine
Nology HotWires for the Mazda Ford KL series V6
มุมมอง 589ปีที่แล้ว
Nology HotWires for the Mazda Ford KL series V6
$40 KLDE cylinderheads, alternator, oil pathways,fuel injector removal
มุมมอง 359ปีที่แล้ว
$40 KLDE cylinderheads, alternator, oil pathways,fuel injector removal
Do you happen to know part number for the blowoff valve?
Awesome to see - inspiring me to install mine finally...
You wouldnt happen to know how much a set of 2 of these would go for, would you? It has custom piping for a 91 300zx TT
@@ScuzzleButt36 I think they go anywhere from 100$ to 250$ each depending on the condition. eBay is where I found mine
@TunasMx6 got ya. Tyvm. Im just trying to sell these and ive had exactly 0 bites in about *checks watch*.... 11 years lol
question how will you avoid the transmission cracking in the future
Have you heard of the Exile Trans Saver? I did a video on it as well
YESSSSSS you just made my day dude and my birthday is 😢 tomorrow you are truly a god send
well happy birthday
This is so cool discovered it by accident mod wise design intrigued me but guessing impossible to find one these days
@@Rickybobby-boosted yeah sometimes you get lucky on eBay and find one
@TunasMx6 sweet I'm keep my eyes open if not may fabricate one
What year is your MX 6 I don't think they will work on my 1997 MX 6. Beautiful results,
Mine is a 1994. to fit the JDM lights you have to do some modification cutting on the frame where the OE headlight mounts.
Sooo... The inlet to the can is from the valve cover and the outlet from the can goes to the rear of the intake, correct?
@@4kocour424 there are two inlets, one to the front valve cover and the other is on back valve cover which a pipe under the intake connects to. The outlet is the filter on top of the catch can. Hope this helps
@@TunasMx6 I thought so! Thanks for the reply. How is the car running with the breather? I read that it could cause a vacuum leak in our cars. Anyway, if I were to run closed system, would simply using a "T" splitter and the having the output into the intake work? I guess it could?
@@4kocour424 Car runs great. That sounds like it would work, and it would be closer to the O.E. setup of the PCV valve system.
thank you for sharing! but why the hks fail? I am ready to add one for my sprintex supercharger. Is there anything I should pay attention to? Thank you.
This style and Generation is one of the older ones. The diaphragm could of been worn out. There was a later Generation HKS bov that sounds the same and it may be better.
@TunasMx6 sir, thank you for letting me know . One more question: Where is the best place to get the vacuum signal? because the sprintex has one by-pass valve, I think have to work toguether with the bov~
@@clodoaldobarros7294 I get most of my stuff off of eBay.
Hi, where did you purchase the front bumper insert? Any link?
Message the eBay seller www.ebay.com/usr/garagefindsnm . He is the one who sold me mine. I think he makes them.
Terry Corner
Fausto Mall
Nya Path
what headlights are those
@@btheben55 Japanese j-spec headlights
where do i find the one piece headlights???
@@btheben55 look up j-spec headlights. Sometimes they are on eBay or the MX6 Facebook group for sale.
At the end of the video 7:38 is that the stock oil cooler your saying to remove/delete?
@@2wheelfamily493 that is the air conditioning core that I deleted at the end
@@TunasMx6 thanks great video btw I have 2 turbo MX6 my favorite cars I've ever owned
Did you you see my white xj
@@HazeGaming111 oh yeah, looks good
@@TunasMx6 yours to we won best 4x4
Garcia Christopher Gonzalez Sarah Lopez Frank
Moore Joseph Thomas Amy Williams Jessica
Onde tem a venda desta válvula ?
I may have missed this, but did the head come with valve stem seals installed?
@@KL.Victor yes, but since they were old I replaced them in a previous video.
@@TunasMx6 Cheers! Not sure how I missed that. I ended up getting Fel-pro seals as well.
This is incredibly useful and valuable information! Thank you for taking the time to put this compilation together complete with parts diagrams and numbers!
Just installed my today
Hey, where is the location for the electric door lock relay?
I am not sure, I never had to fix mine or mess with it. haha.
@@TunasMx6 Ok, thanx.
Im amazed its staying together mine with a singal type s and a 5th gen m45 was blowing the pipes off beaded and tbolts with hairspray
@@jeffgood6441 thats not good. my type s has been great with no issues so far
I have a 5th gen m45 mounted there same setup basically intercooled too
Hi I'm just assembling my engine and I notice my oil pump have some cracks under where the relief valve plug is like yours, on the original. is it normal? I have another, but older (92) that doesn't have it.
Not sure if it is normal, but the pump was working great with no issues at the time.
Very Helpful!
Love to see some mx-6 love in 2024!!! Flashback to 2002. 18 year old me, F&F came out. senior in high school. Bought a 93 ls with borla exhaust, lowered, wheels, etc. Loved every minute of it. Something about the sound of the kl is chilling. Kept it for years and sold a couple years ago. Kinda regret but I would buy another one for a project in a heartbeat.
Nice clean car. Never seen more than a few MX-6s on the road. Never seen 3 cooling fans either...
Hi, l'm Carlos from the Philippines, l am interested to buy the nology wire for my Toyota Altis 2014. I checked the Lazada and shopee, but to no avail. Can you help me Sir?
I would email them at Email: General: support@nology.com Sales: sales@nology.com
Thanks for uploading, so happy to see fresh MX6 content in 2024 :)
Would be nice to share how do you get this bits together just had mine delivery but not sure how to assembly them ? Thanks
Your videos is helping for mi own rebuild of klde engine from my car. Thanks from Spain 😁🤙. And sorry for my bad english 😅
Hi again, for the o-ring bipass from the block to the heads wich oil rings are you going to use and where can I buy it 😬
I thought the egr was under the car in the exhaust system with these engines?
The egr vent exhaust tube is under the right exhaust manifold, but egr is on cylinder head on this klde
@@TunasMx6forgot to mention it like engine sputters like a wierd misfire
Hey guy. Just letting you know I fully appreciate your ride. I had a 93 mystere with the silver mx6 kick plates, black on black leather. I wish I kept it. Take care!
Thank
Thank!
What switch panel is this?
Autopilot v2 AirLift Performance
do you have a comparison of the factory rod/piston weight? I don't really need a stronger motor but I want to build a lighter, perfectly balanced, high comp motor that can take sustained high revs
Unfortunately I didn't measure the oe rods/pistons.
Shit are you having a mid life crisis 😂
buddy, you are planning to do a full review of your cool car, tell us about the work you have done, what you built it from and what you are planning, post a beautifully photographed MX-6 as a preview, enjoy watching this whole video + such a video will be easier to get into the charts ?
Looks great man.
Miss my mx6, my first car was an m-edition, they will always have a special place in my heart...nice channel bro...i found tgat old M-edition but shes in bad shape if i can afford it I plan to go get it...too many projects right now tho...keep it up man.
Thanks
Nice...
Not a bad price, My brother in law used mine to melt plastic in 😫😫😫, Still works though.
When you are finished with the the engine, please send it to Ggermany 😄 I´m jealous that you have so many parts for the KLDE. there are few parts here in Germany. You are doing a great job. I like to see your progress. 😏👍
Haha, thanks
Solid work all around
Thanks for the tutorial. Nice setup. I have a Ford Fusion. Would you recommend 1/4 lines or 3/8?
I think 1/4 inch is fine for most setups unless you are doing a fast bag setup
That´s a sick setup mate! I have a question for you. If I have an stock 1994 PGT and want to connect my oil catch can the same way you did, what can I do with the small air port at the intake elbow and the other at the intake manifold? I can see there is a hose that goes from the PCV valve to the intake manifold but you unplugged it from the intake manifold and connected it to the oil catch can. What did you with that port at the intake manifold where you disconnected that hose from? Did yoy just capped it?
You can cap off / plug up the intake ports. Let PVC vent through the catch can.
Здравствуйте очень интересна эта история про его так как у меня Мазда милления на kl ze 2.5 и так же висит ошибка по егр но мотор из Японии и самого клапана нет хочу как то закрыть вакуумную систему до конца но висят все солинойды на егр и не знаю как их соединить что бы вырезать лишний солинойд из системы.