วีดีโอ

@@jjophoven that is why it is messed up that has been fixed if you check the other videos

@@caffeiphile you do not have to have a valid level 2 accent the main thing that is looked at is that there is not contact with the match and the top rung at the same time. We have done this in composition

@RoboRangers-FTC oh my bad. Anyways, nice climb.

@yea try w game reveal made it seam like that but the team updates say differently

@@PeytonYeung it is above the low runs

We use the short viper slides from Gobuilda

@@Microplastic64 like the linkage is

@@moham3713 what

@ There is a virtual play to qualify do you have the site where we can play

@ we do not cause we have never heard of that

@@Jsjrjekdjebek the small gobilda viper slides don’t remember the size

@@RoboRangers-FTClike the ones not already pre built like the singles?

@ yea just 2 single sets of the short viper alides

@@RoboRangers-FTC so what did you use to get them to move like did you do it by urself is there I guide and did you use something else bcs string does not work horizontally in our experience we only used iko slides before

@ there’s two linkages that’s ran by a servo

@@pootis8346 what two bars

the one you guys use for your linkage

@ they are just two of the short viper slides goBuilda sells

@@kkenekii5778 at first we only have 1 but we realized that if we did not a a grip on both sides we would not be able to clip so we had to add it

@@ortega9115 we are having the slides run to a position and stay there using encoders and same going to any position

@ oh sick! Ill have to tell my team's programmers to try that, thanks!

@@RileyMathewson-e9x that are just parts from goBuilda

@@TimmyPham-ed6ym it is just build a rubber feet

@@tanitolorunakinyemi3435 it is not fully automatic just in case we get a bad grab it set a middle point that our driver has to push a button to go to the next transfer all the way out

@@Darkcamera45 it is not adjusting it is just giving our human player prep time by hovering around an area so he can line it up correctly

@ I see thx for the clarification

@@vishufortnite8401 did you bring up the Q&A forums or the game Manuel team update 5

​@RoboRangers-FTC it says in an update while ascending not ascended, believe this means you can use it to climb to level 3, but just using it at level 2 will not count.

@ well we should be going for level 3 by our next one so I hope it counts

@@RaghavKaushik09 I don’t we do not use pedropathing

@@RoboRangers-FTC do you just use motor encoders? if so, do you use time based, rotations, etc.

@ it counts the rotations/encoder counts of the motors

@@RoboRangers-FTC thank you so much

@@douge9223 there are button head screws that attach through the slides snitch are attached at a 90 degree angle thing

@@parallelfifth9505 no they’re just goBuilda viper slides they have just been broken in for 3 years

@@RoboRangers-FTC Ah got it. I'm wondering if the linkage system in the horizontal ones was intentional for speed or because of space constraints? It's quite clever and the slide seems to move along quickly.

@ it was for both reasons because we didn’t want to use a motor to power the horizontal slides and save it for a hanging motor servo is moving that little space can cover a lot with that long linkage

@@ryanyu3626 yes they are

@@ryanvandenbosch7772 your slides motor have to be able to also

@@JoshuaThe-xp2jb you are allowed to adjust the specimen as long as you were grabbing the outside part of the clips you are not breaking the plane of the field wall while the robot is in the observation zone check the q&a forum Q18 and Q145

@@F4TELamont the ones on the claw are go builds torque servos and the ones that rotate over are axon max servos

@@zekecohen298 we don’t have much time to meet with people what are yall wanting to understand more of

@RoboRangers-FTC my team is struggling a lot with conserving space as well as resources in terms of building... aswell we wanted to take a similar approach of using servos to power slides, and wanted to know if you can give a more in depth explanation on that

@ I can see what I can do and try to find a time around like 4:30ish to try and help yall out as much as i can

@RoboRangers-FTC what day would that be for? We primarily meet on Fridays, but Mondays and Wednesdays work as well... honestly, any day except sundays can work. we can always make time

@ i d in not know at the moment as I have to figure out my schedule next week but I think Wednesday probably it friday

@@sohum5905 so we track the encoder wheel counts and place that on a coordinate plain and tell the robot to move to those coordinates and to do so with a specific heading

@ ahhh ok 👍

@@RoboRangers-FTC do you guys use roadrunner

@@sohum5905 no we do not

@@Knighttwister you are correct but we are not going for level 3 at moment only level 2

@@sk-mi1kb what do you mwan

@@JoshuaThe-xp2jb that is exactly what we are using

Fuck no

@@0xCUBE the vertical slides are ran by motors but the horizontal slides are ran my servos

dc motors? what gear ratio are they

@@Funky-G they are 312 rpm

@@0xCUBE yes we do right now we have a husky lens planted beneath the claw which help a little bit later we are also planing to have a rotating claw to help with that was well

@@GitikGitous what would you be looking help for

@ We have some troubles with CAD.

@@GitikGitous we would not be able to help with that as we do not do much if any CAD

​@@GitikGitouswhat program?

@@bobbobberson2496no i mean RoboRanger’s robot CAD. I use fusion 360 .

@@maheshdhingra8265 what

the first 30 seconds was auto, but the last 2 mins was teleop

@maheshdhingra8265 what do you mean

@@RoboRangers-FTCi think he meant like the gobilda starter kit, etc

@ I see

@@maheshdhingra8265 The bot is not assed off the starter kit but ig it would be the closest to the go build grip force chassis kit

@@kkenekii5778 I believe 9-10

@@kkenekii5778 they are the the 240mm slides and there are two stacked