TechScience
TechScience
  • 30
  • 108 351
How PIR Sensor Motion Sensor Light [ DIY ]
H: Repeat Trigger Mode:- In this mode light will be continuously ON if there is motion and when there is no motion light will turn OFF after delay time.
For example; If the delay time is set to 10seconds then, Light will be continuously ON when motion is detected and when you leave the detection area the Light will turn OFF after 10 seconds.
L: Single Trigger Mode:- In this mode Light will turn ON when motion is detected and light will turn OFF after Delay time. Light will turn OFF after delay time even if you are present in the detection area and again after some time sensor module will start detecting any motion
Turn ON the circuit, wait for 30 to 60 seconds now sensor will start detecting any motion in its range and act according to the mode selected. [This module will only detect motion done by any warm body such as human or animals]
Mode can be selected by adjusting the Jumper,, how??-- pull out the jumper, you will see three pins now put back the jumper to the H side or L side leaving one of the pin blank.
Sensitivity Adjust:- we can adjust the sensitivity or detection range of the sensor by adjusting the preset @ 0:21 . The detection range can be adjusted between 3 meters to 7 meters.
Delay time adjust:- when you leave the detection area Light will turn OFF after some delay; this delay time can be adjusted by rotating(clockwise or anticlockwise) the preset @ 0:22 .
This delay time can be adjusted between 5second to 300seconds.
Both the preset can be adjusted by slowly rotating it clockwise or anticlockwise; You can use a small screwdriver to rotate these presets
มุมมอง: 273

วีดีโอ

SERVO STABILIZER CONTROL CARD WIRING
มุมมอง 18K3 ปีที่แล้ว
Servo Stabilizer Control Card Wiring with in 10 minute
Servo Control card double display card 90v
มุมมอง 26K3 ปีที่แล้ว
Servo Control card user setting factory setting calibration
How To Add Multiple Layers In A Pcb
มุมมอง 2313 ปีที่แล้ว
How To Add Multiple Layers In A Pcb
Double Side Pcb 5V Regulator Design Altium
มุมมอง 7993 ปีที่แล้ว
Double Side Pcb 5V Regulator Design Altium
3 phase Timer User Manual | Astronomical Street Light Timer
มุมมอง 3123 ปีที่แล้ว
Intelligent Power Saving Astronomical Light Device This Model Can be programme and change the feature as per required timing. There are four keys for input data and One LCD for User Interface …and Two Leds. ROTATION LCD DISPLAY High Bright LCD Rotation LCD display Various Parameter in Cyclic Mode. if User wants to change to Next Screen User can press Shift Button Momentary. FOR SELECTING FIX TI...
Astronomical timer street light timer
มุมมอง 2253 ปีที่แล้ว
3 Phase Astronomical Timer Hi Friends..3 phase astronomical a smart Device to control the light instead of using manual / tradition method of turning on and off light manually. what is Astronomical: if we are knowing the location info , Day of year , and time zone then we can calculate the sunset and sunrise time of that place. using this logic our device calculate sun set and sunrise time of p...
STM32 URAT
มุมมอง 1443 ปีที่แล้ว
Hi Friend , This video will show the demo of UART communication with PCB ..on STM32f030R8T6 UART is hardware that is not clock based, it's timing based. there will be two line RX TX of micro That will connect to TX RX of PC or other communicating device the main parameter are Baud rate ...9600bps ..this can be vary as per requirement parity ..for safety even/odd stop bit ...1 or 2 as per choice...
How does an Electric Motor work? (DC Motor)
มุมมอง 773 ปีที่แล้ว
Electric motors can seem very mysterious! How do they use electricity to start rotating? Let's break it down step by step to understand how it works. Topics covered in this video: circuits, current, magnets, electromagnets, armature, commutator, brushes, stator, and rotor. This video only covers DC motors.
machine to modbus
มุมมอง 1853 ปีที่แล้ว
machine to modbus
Mri Machine working
มุมมอง 993 ปีที่แล้ว
Magnetic Resonance Imaging, commonly known as MRI, helps doctors find, watch, and treat medical problems. MRI uses very strong magnets, radio waves, and a computer to make pictures of the inside of the body. MRI pictures are more detailed than those made with other methods. There are many reasons to have MRI. MRI may find bleeding, such as bleeding in the brain; brain, changes as in stroke; pro...
How Ignition Coils Work
มุมมอง 1603 ปีที่แล้ว
Conventional automobiles burn gasoline in an internal combustion engine and convert that energy into motion. But first a spark is needed to ignite the fuel mixture. This animation shows how a 12-volt battery generates the high voltage required to create such a discharge
Capacitors Explained - The basics how capacitors work working principle
มุมมอง 1263 ปีที่แล้ว
Capacitors can store electrical energy and discharge it quickly, powering things like flash bulbs and starter motors
Stm32 clock gpio
มุมมอง 1523 ปีที่แล้ว
This video is the first in the Register Based Programming Series. This covers the clock Setup and GPIO Setup for LED blinking
Stm32 Clock 1
มุมมอง 1743 ปีที่แล้ว
The Clocks is a very important part of the configuration of your Cortex Mx. All Cortex Mx have one or more internal oscillator (RC) and one or more external crystals oscillators (Xtal). s a must to use the eternal clock for RTC and also for high speed serial communications (Ethernet, USART, etc). Below there is a comparison from internal clock (RC) and external clock (crystal clock). The top of...
GSMRS232Converetr
มุมมอง 3013 ปีที่แล้ว
GSMRS232Converetr
STM32 INTRO
มุมมอง 1833 ปีที่แล้ว
STM32 INTRO
ADC on STM8S Reading Analog Voltage from Potentiometer
มุมมอง 1.7K3 ปีที่แล้ว
ADC on STM8S Reading Analog Voltage from Potentiometer
Stm8 Switch Interface
มุมมอง 3323 ปีที่แล้ว
Stm8 Switch Interface
stm8 timer
มุมมอง 2K3 ปีที่แล้ว
stm8 timer
STM8 PART 3
มุมมอง 8783 ปีที่แล้ว
STM8 PART 3
Stm8s Basic setting and coding
มุมมอง 6K3 ปีที่แล้ว
Stm8s Basic setting and coding
stm8 cube
มุมมอง 4.4K3 ปีที่แล้ว
stm8 cube
Single Sided PCB Design
มุมมอง 7933 ปีที่แล้ว
Single Sided PCB Design
altium gerber file generation | Tutorial for Altium Beginners: Generating Manufacturing Outputs
มุมมอง 1.2K3 ปีที่แล้ว
altium gerber file generation | Tutorial for Altium Beginners: Generating Manufacturing Outputs
Altium Designer Schematic Library | Altium Designer | Tech Science | Altium Designer In Hindi
มุมมอง 4.8K3 ปีที่แล้ว
Altium Designer Schematic Library | Altium Designer | Tech Science | Altium Designer In Hindi
Metro Indicator | Dot matrix 8x8
มุมมอง 2823 ปีที่แล้ว
Metro Indicator | Dot matrix 8x8
How to Start a Project in Altium Designer | Altium Designer tutorial in Hindi
มุมมอง 6K3 ปีที่แล้ว
How to Start a Project in Altium Designer | Altium Designer tutorial in Hindi
How to use multimeter in hindi | Multimeter tutorial | multimeter kaise chalaye
มุมมอง 4.3K3 ปีที่แล้ว
How to use multimeter in hindi | Multimeter tutorial | multimeter kaise chalaye
servo voltage stabilizer control card
มุมมอง 29K3 ปีที่แล้ว
servo voltage stabilizer control card

ความคิดเห็น

  • @Mkdhiman-hj9is
    @Mkdhiman-hj9is 12 วันที่ผ่านมา

    Sir output nahi nikal raha

  • @adityasahusahu6630
    @adityasahusahu6630 22 วันที่ผ่านมา

    Bord chahiye to kha se milega

  • @nishkarshcharan6337
    @nishkarshcharan6337 หลายเดือนก่อน

    Sir isme input tapping vary karti hai aur output tapping fix hoti hai na. I mean supply phase vary karta hai carbon ke dwara

  • @abdulraufnighyal4064
    @abdulraufnighyal4064 หลายเดือนก่อน

    No doubt that you have good knowledge but it will be much better that before demo study your self to avoid any mistake

  • @HarendraSingh-fi5cf
    @HarendraSingh-fi5cf หลายเดือนก่อน

    Sir how to on the controller

  • @RAmeezMahmoodRws695
    @RAmeezMahmoodRws695 หลายเดือนก่อน

    Kindly guide me how to run st visual program in win 10.

  • @RAmeezMahmoodRws695
    @RAmeezMahmoodRws695 หลายเดือนก่อน

    Is stvp work win10?

  • @prakashdangi208
    @prakashdangi208 หลายเดือนก่อน

    सर आपके कल नम्बर पठाई दिईए

  • @santoshjha7203
    @santoshjha7203 3 หลายเดือนก่อน

    Thank you sir

  • @girirajyadavkotaraj
    @girirajyadavkotaraj 4 หลายเดือนก่อน

    ये कंट्रोल कार्ड कितने का आता है

  • @AbhishekKumar-pb5sh
    @AbhishekKumar-pb5sh 5 หลายเดือนก่อน

    Sir your contect pls send me

  • @samirpatel2585
    @samirpatel2585 7 หลายเดือนก่อน

    Sir aap kaa number

  • @alpeshdarji7340
    @alpeshdarji7340 7 หลายเดือนก่อน

    Please sir give me your number

  • @tejpalyadav5864
    @tejpalyadav5864 8 หลายเดือนก่อน

    Company details send me plz

  • @tejpalyadav5864
    @tejpalyadav5864 8 หลายเดือนก่อน

    Company details send me plz

  • @rakeshkumawat2708
    @rakeshkumawat2708 9 หลายเดือนก่อน

    Nice bro

  • @a.s.m.r1913
    @a.s.m.r1913 9 หลายเดือนก่อน

    sir apka nmbar do

  • @prakashdurge9357
    @prakashdurge9357 10 หลายเดือนก่อน

    3phase wiring

  • @user-rv2bw8by9w
    @user-rv2bw8by9w 10 หลายเดือนก่อน

    Bhai 121 3524 Driver ic Moc 3021 Scr Driver 4n35 optocupler Lm324 Comparator ic based local inverter kit par vidro

  • @131-priyanshchouhan6
    @131-priyanshchouhan6 10 หลายเดือนก่อน

    What is Hysteresis voltage setting sir

  • @mohammadabid971
    @mohammadabid971 11 หลายเดือนก่อน

    I want to read AND wright STM8S903K3T6C

  • @surajkumar-ln8kr
    @surajkumar-ln8kr 11 หลายเดือนก่อน

    Saras ko purchase kahan se kiye the aap timur aur display ka humko bhi purchase karna hai

  • @user-pz7zt9mp6x
    @user-pz7zt9mp6x ปีที่แล้ว

    Output input canecsn kese. Hota hai

  • @comedy99913
    @comedy99913 ปีที่แล้ว

    3 phase servo k card m out put 340v de Raha h tho card m kya kharab h please reply

  • @hariomtechnician
    @hariomtechnician ปีที่แล้ว

    सर इसको इनपुट 130 वोल्टेज पर कैसे सेट किया जाए यह यह बता दो

  • @dhayacreations243
    @dhayacreations243 ปีที่แล้ว

    Where can i get this card for purchase

  • @jituraaz8895
    @jituraaz8895 ปีที่แล้ว

    Mo no do

  • @jituraaz8895
    @jituraaz8895 ปีที่แล้ว

    नीचे का डिस्प्ले एलइडी लाइट नहीं आ रहा है उसका उपाय बताइए

  • @hemangangber8309
    @hemangangber8309 ปีที่แล้ว

    without realy wale stabilizer me ye card work karega kya

  • @hemangangber8309
    @hemangangber8309 ปีที่แล้ว

    भाई मेरे पास 3kva servo stebilizer है जिसमे manula, इनक्रीज, डिस्क्रिज सभी button है लेकिन मैं जब ऑटो 230v fix करके रखना चाहता हूं तो 12v से चलने वाली circuit bord की कुछ पार्ट्स जलती जाती है इसलिए मैं इनक्रीज डिस्क्रिज बटन से उपयोग कर रह हु तो क्या मेरे stebilizer में डिजिटल circuit बोर्ड फिट हो जाएगा क्या please बतायें मुझसे🙏

  • @hemangangber8309
    @hemangangber8309 ปีที่แล้ว

    भाई मेरे पास 3kva servo stebilizer है जिसमे manula, इनक्रीज, डिस्क्रिज सभी button है लेकिन मैं जब ऑटो 230v fix करके रखना चाहता हूं तो 12v से चलने वाली circuit bord की कुछ पार्ट्स जलती जाती है इसलिए मैं इनक्रीज डिस्क्रिज बटन से उपयोग कर रह हु तो क्या मेरे stebilizer में डिजिटल circuit बोर्ड फिट हो जाएगा क्या ?

  • @hemangangber8309
    @hemangangber8309 ปีที่แล้ว

    5kva ka price kya hai

  • @shekharrathore7331
    @shekharrathore7331 ปีที่แล้ว

    Static stabilizer b mil jayega kya

  • @ramprakash-ti2xc
    @ramprakash-ti2xc ปีที่แล้ว

    Aapka servo card kitney ka hai

  • @OnceARider
    @OnceARider ปีที่แล้ว

    Meter matching mode me output voltage kahan se check karenge, I mean multi meter kahan connect karna hai?

  • @carloscamsaparelhos
    @carloscamsaparelhos ปีที่แล้ว

    Bom dia tem como quebra a segurança do STM8s005k6 , se tem pode ajudar por favor, estou com 2 aparelhos um esta com programa com fala o outro esta bom mais protegido , desejo copiar o programa para salva o segundo aparelho com defeito

  • @abdulwaaseihsultan7733
    @abdulwaaseihsultan7733 ปีที่แล้ว

    Hi one question please. In this regulator you have AC motor. If we have a DC motor to control what we will do?. Kindly answer

  • @ramjisharma2012
    @ramjisharma2012 ปีที่แล้ว

    Spare parts kahan se len sir please website number dijiye

  • @ramjisharma2012
    @ramjisharma2012 ปีที่แล้ว

    Thank you sir

  • @skash230784
    @skash230784 ปีที่แล้ว

    Kindly send me your contact details

  • @bgh776
    @bgh776 ปีที่แล้ว

    H lmt and l lmt kya hai?

  • @renuchandel9863
    @renuchandel9863 ปีที่แล้ว

    Is kat ki dayr rng dekay

  • @wrmarohit
    @wrmarohit ปีที่แล้ว

    Sir mera card nhi chl rha

  • @wrmarohit
    @wrmarohit ปีที่แล้ว

    Sir mera card nhi chl rha

  • @sainisunil306
    @sainisunil306 ปีที่แล้ว

    Bhaiya mujhe card lena kahan milega

  • @akramdjsikta4444
    @akramdjsikta4444 ปีที่แล้ว

    sir aap ka shop kaha pe h..

  • @vishal.chawla
    @vishal.chawla ปีที่แล้ว

    Can we read hex file from stm8s903?

  • @alokbansal8229
    @alokbansal8229 2 ปีที่แล้ว

    How to get this card. And what is the price

  • @letslearn4funn
    @letslearn4funn 2 ปีที่แล้ว

    3 phase dimmer ke liye ek hi controller lgega ya alg alg 3 digital controller chahiye

  • @etcetc6653
    @etcetc6653 2 ปีที่แล้ว

    यूपीवीसी प्लेट कहां पर मिलेगी इसका कांटेक्ट नंबर दें