วีดีโอ

send an email darok8@gmail.com

Hi, The I/O Overload trip indicates that the total current drawn from 24 V user supply or from the digital output has exceeded the limit. A trip is initiated if one or more of the following conditions: • Maximum output current from one digital output is 100 mA. • The combined maximum output current from outputs 1 and 2 is 100 mA • The combined maximum output current from output 3 and +24 V output is 100 mA Recommended actions: • Check total loads on digital outputs • Check control wiring is correct • Check output wiring is undamaged

drive.google.com/file/d/1tt83I22AJsbxLJ4J9uJ5yCM7OI13Kxc7/view?usp=sharing

drive.google.com/drive/folders/1cPKlobJNHGb__dzML2XI4aygyK3e0gLk?usp=sharing

@@_mectel Thanks a lot for sharing the Link

Gracias por comentar, que bueno que te fue de ayuda

Hi, Its an application on the SI-App module

In the same way, it can be by modbus rtu/tcp, Profinet

You're welcome, it's good that it helped you

drive.google.com/drive/folders/1cPKlobJNHGb__dzML2XI4aygyK3e0gLk?usp=sharing The Logic Master software is in this link, also VersaPro

Hello, thank you for your comment, I did not change any parameter to enable communication, it is possible that if you cannot establish communication there is a problem with the processor card.

drive.google.com/file/d/1XubZguleHs1xLR8dA0V2fL9riFltsZpY/view

Hola, en el lado de la PC puede ser un USB o si tiene puerto nativo serial con RS232, en el lado del HMI dependerá si tiene puerto RS232 o RS485.

Hi, is an Application from Control Techniques

Hello, how are you, thank you for your interest, how can we support you?

Hello, good day, I recommend you make a backup of the Drive before changing parameters and then check if it has a voltage of +10Vdc with respect to 0V, connect your potentiometer or your analog input and see if the analog signal is reflected in parameter 1.17

Thanks for the fast reply In parameter, there are variables nunbers as potensiometer words but no voltage out If can I contact you on WhatsApp number?

There is voltage +/- 10v and 24v

Check the parameter 1.17 show the status of analog input, it match 0 to 10Volts with parameter 0 to 1000 on parameter 1.17

Hi, There may be several reasons for this message to appear, in my case, it was the y10 parameter, which must be set to 1 (FRENIC Loader protocol), but it is recommended that you review the complete set of parameters, which goes from y01 to y10. Greetings

How can I help you?

@@_mectel sir,do you know how to autotune mentor 2 drive.i followed manual,but then it is showing field loss trip and the procedure cannot complete.

In that case you will most likely need to deactivate the field lack alarm by programming parameter #10.29=1

Nunca he tenido problema al instalarlo, ya probaste en Wxp? o en otra PC?

Hola, el tema de los cables parte desde crear cada capa de cable, para esto, las puedes crear en el apartado de "Edit Wires/Wire Numbers" enseguida en "Create/Edit Wire Type", ó si prefieres con el comando AEWIRETYPE desde la barra de comandos, en el cuadro de dialogo crea tus capas de cable, con características de color, tipo de linea y espesor, una vez creada la capa, cuando vallas a colocar un cable tienes que tener seleccionada la capa del cable que deseas colocar, una vez colocado el cable, ejecutas la instruccion de colocar la etiqueta del cable, mediante AEWIRECOLORLABEL

Gracias por comentar, que bueno que te fue de ayuda

drive.google.com/file/d/1XubZguleHs1xLR8dA0V2fL9riFltsZpY/view?usp=sharing

@@_mectel Sir, this use USB to RS232 or USB to RS485 converter?

@@ronaldhalim9055 The connector side of PC is a serial DB9, If your computer have not a serial port native, you have to use a USB to serial port

@@ronaldhalim9055 Is a serial port RS232

@@_mectel Thanks for your help Sir

No lo se con certeza, pero pienso que no es posible, o al menos si fuese posible se convertiría en formas simples sin propiedades ni atributos, no seria funcional muy seguramente.

Gracias por comentar, que bueno que te fue de ayuda

Hi, how can I help you?

How can I help you?

@@_mectel i am working on this drive. I have done a lot of things but now failed. Could you please send me configurations?

@@farhanmunawar8518 Specifically what is your problem, your comment is very general, I don't know how to help you

Sir i was working on a rotary cutter Machine with this same technology. Unfortunately i cannot parameterize all. So i need your help if you share specific parameters

@@farhanmunawar8518 Whats is your email

Yo en tu lugar probaría la animación desde el simulador "Off-line Simulation" si trabaja en off-line debería funcionar en la PC, en caso de que continúe no mostrando la animación, prueba con otra PC.

@@_mectel Ya he probado con 2 computadoras más, en modo Offline y realice la simulación entre el DopDoft y Ispsoft y si funciona las animaciones y todo lo que quiero mostrar en pantalla me parece extraño lo que me sucede :(. No se si se deba a que el PLC en un poco antiguo (DVP10SX). Gracias por tu comntario

Gracias por comentar, que bueno que te fue de ayuda

Hi, how can I help you?

Hola, de donde eres?

I want to studi to...i'm from Indonesia

@@nurulichsan1671 Give your email

Te recomiendo esta serie de videos th-cam.com/video/Q5RG9pt7Z9E/w-d-xo.html son 4 videos (mas de 4hrs)

th-cam.com/video/IDIa18Ozd58/w-d-xo.html

Hi, @Nesih It depends on the scope of the project, but I don't think it's possible, due to the number of variables to be controlled and the memory capacity of the internal PLC.

@@_mectel tank you

@@nesihcoban1138 Hello, I saw your comment again and I understood the question, the answer is Yes, the RotaryKnife system can be done with the native Drive encoder inputs, the SI-Encoder is not essential, the previous answer was regarding the use of SI -APP.