วีดีโอ

Thank Yoooooooooou for this video.

Do you know a Gigabit adapter injector? I can't find one that is cheap also looking for a solution with the cable line end if I choose to use poe switch then the other side needs a stepdown to 12v but the problem is I hate to use injector splitter because the power maybe unreliable cause the wifi or the accesspoint to messed with the signal and IP addresses . that's why I'm also looking for a stepdown that I can attach before the balun connector

Thanks, helpful.

thank you, it works

nice video English chap

*Promo sm* 👌

When I enter 'do show interface description' command it says invalid entry. Update from packetracer?

removing Access-group 10 from vlan 4 is equally causing damage to the network/clients like you try to remove one single entry from the statement...instead just copy the statements to your notepad add the permit or deny statement and go back to the router and paste all of them

Thanks for going over the aaa new-model issue, that really helped me out.

after I copy/save configuration, I have no idea where it saved to and connot seem to find it. is there a default location its being saved to? I would like to upload that config file to a few more access points. thank you

Thank you on explaining RX/TX load.

Runts are frames received its size is less than 46 bytes that is 0 mean no runts received (if it receives it would not discard it will do padding add extra bits to make it 46 bytes to make it transferable), Giants are frames those size is over 1500 bytes ( and it did not drop it, if it receive giants it will do fragmentation and then send) and giants frames received are 0 at the moment in this interface.

This is very helpful

thanks mate!

How to condifure remote desktop access lan ip from wan ip pc in sonicwall 240

Thanks a lot for this video, It really help me to be able to include the show running-config command in a read only mode. Thanks again

Muchas gracias, me ayudó bastante

Brilliant! thank so much! im going hand-on!

This is partially correct and still not allowing the service to pass

Tanks for the information.

@Darkdrey on telegram is a real vendor I can’t believe my eyes that man too real Go on his telegram He sell credit card with high balance💯

TPOT

Salute your memory in remembering each and every line of the command output. Nice work & thank you for sharing this with humanity :)

Can you send explain this video on paper . I will translate it to Arabic language

It's cool how you explained everything- how did you learn all of this?

This was great! I need to setup a similar rule and I’m novice at best with networking but trying to sharpen my skills more! Thanks again! Great tutorial!

Well done! Thank you!

Dude. You saved my ass!!! Had some trouble poking holes thru this sonic wall. Your tutorial made it happen. Thanks Alot !!

Thanks for this tutorial. What is "Wireless Access Point MIB" with the same version number. You can download the "WAP121_1.0.6.8-mibs.zip" file on the same CISCO page. Is it something in addition or the firmware in other format?

Very Useful information to secure the remote management. Thanks for sharing.

thank you. productive presentation.

why "show interfaces status" doesn't work in packet tracer? However " show interfaces" commands works fine.

Thanks for sharing! Is there a way to translate a different WAN port to HTTPS management? I am having trouble finding it, but perhaps I need to look at the WAN-WAN rules..

Thanks for updating like this...keep posted more videos on CLI and troubleshooting

The lower SNR means a higher speed , The higher SNR means good stability . I don't quiet understand :/

Good concise example and tutorial. would help if you list or put an annotation on the screen, which sonicwall (example :1) / your working on and the machine ip. Cheers ~~

Very helpful! Thank you for making this.

i have a question about the bit to enter the serial interface to start, I have ping from my pc (ping 1.1.1.2 -l 1000 -t) on the other router (WAN CONNECTON) and when I'm on the router that I ping him with the show interface serial command 1 / 0 and in (30 second input rate 0 bits / sec, 0 packets / sec) I received only 8000 bits while than the transmission ping contunu (ping 1.1.1.2 -l 1000 -t), but why I always receives 8000 bits and my ping always contunus.

I have

Great explanation, congrats, I got a question, in this example the total of input is ~1,516 Mb and output traffic is aprox. 1682Mb ?

if I add my public IP which i'am using in Home to management group to restrict access to sonicwall HTTPS management through WAN that IP not static, if I restart the DSL modem I will get deferent Public IP after that I can't access my sonicwall through WAN,I add my computer mac address to management group, also not successful, could you please give other solution for that to be fixed.

Thanks for the detailed explanation.