วีดีโอ

I need AJ to work on my Rover!

We appreciate people like him 🙏

Love those cars even if the timing chains are a nightmare lol. My oldest son had one for a little while and traded it for a 99 Chevy 1500. I miss it

Legend buddy legend

Well what was the problem?

Do you know I don’t know what kind of car that is and I don’t know if you’re doing this for money fixing somebody’s vehicle but if it’s a car worth doing a steering rack and spending all that money to go the extra distance and encourage them to buy all new lines. It’s really kind of a thoughtful thing to suggest because the debris that’s in those old lines, it’s just gonna start wearing out that steering rack with contamination so you know I don’t know. I would certainly replace all the lines going to the extent of putting a steering rack in a car as well as possibly even putting a new steering pump in so that you’ve got a whole new thing is probably maybe a little more than twice the expense perhaps but if somebody’s gonna put that money in it, they’re gonna probably keep the car and I don’t think it’s real and at least replace the lines. No offense, but certainly up charge and after our steering rack is really not that hard. It’s a profit margin and doing a steering rack is up as 1 million bucks. It’s not really that hard.

Bearings may be worn past tolerance and the engine might need serious work. What’s the oil level on the dip stick?

I’ve got a 2014 SXT AWD Charger, that was a ex-police/security car. Low mileage (only 117,000km (73,000mi). When it got cold a few weeks ago, the car wouldn’t start (no crank, no start). My cousin and I boosted it and managed to get it to run, so I took it home and put in the garage. My dad and I changed the battery the next morning, however the car did the same thing that night when it was left outside. This past week we changed the starter, however the car is having the same issue. It did throw the U0101 code yesterday which it didn’t throw before, so could the TCM have been the cause from the beginning? Or could it be a different electrical issue?

I’m going to replace mine in a couple of weeks. I came across this video while looking for some tips on TH-cam. I have a question and hope you are still monitoring comments. Do I still need to remove the motor mount when I’m removing the old gasket?

Been looking at that tool

Supporters of the Chevrolet lacetti (Suzuki Reno)???

I have a question, On the torque specs, use 71 inch lbs for the valve body and 53 inch lbs for the lead frame assembly. My torque wrench I can only get 50 or 52 inch lbs and 52 or 53 inch lbs. Which one would you recommend?

Ty for sharing. Will tackle this today. God bless you

Holds 5.5 qts. Oil

Proud of you Liam!❤

You didn’t show removing the console to get to the usb ????Do you have that ?

thank you for your input on helping makes it it a s lot faster and i feel very profesional😀

Is the oils sensor for a 2007 Sedona in the same spot?

my oil cooler pipe burst on 2008 Toyota Kluger Feb 2023,Toyota Australia recalled this part in 2019 and paid for replacement but they knew this was a major fault but took their time in fixing it, just should have always been metal

Pop

Good video. Always something to cause an issue.

I doing my 2014 Sorento 3.3l this weekend. Going to just get the kit to do it all while I have it open. I know I need a timing cover gasket set, but any other gaskets I should pickup before i get started?

How can the locking pin be fixed?

What if the amp doesn’t show up on the screen at all?

no torque listed on nkg box install and tighten 1/4 turn works great

Would it cause the engine not to start

I changed my 8th gen accords crankshaft sensor, car still in limp mode after replacement, do I need to have it diagnosed?

Thanks so much for sharing your work, and telling what you used for tools. I ve got to do this job and I am dreading it. May take me all day. Thanks again.

Thank you

You are the man! Thank you! I feel better now.

Thanks for the video. Is it worth putting some anti-seize on the new hub where it goes into the knuckle to make it easier next time? Have you done a bearing hub on a 13 Lincoln MKX? Pretty sure mine needs replacing and wondering if I should go out and buy the Hub Shocker or just use the bolt/nut method to pull the hub out?

Too video mate. When using a power probe, once the new pads are in, do you use the power probe to push it back out?

Never understand the power tool to take 3mm bolts out??? They sale hand wratches.

Quick and to the point. Thank you!

Hey, how you doing again, sir, I see you?In another video fixing on the same range.Rover, you have the engine taken aparti.Would like you to take a look at mine's if possible?And I will pay you to repair it need

AJ, are you in Georgia? I have the same Range Rover. And I need mines rebuilt or high pressure fuel pumps replaced or something, they said if you can hit me back.

I’m working on a 2017 Chevy Cruze same set up as this model in this video. I bellowed your steps in this video picture by picture, and when I go to start up the car, it doesn’t want to turn over but struggles to turn over and when I go to check why there’s fuel all inside the the block where you show your spraying out the gas to dry it out. So, please get back to me and tell me what I did wrong? Btw after my third attempt I am trying to find the new o rings to replace.

A question, brother about the intake cam, the synchronization part, the one that rotates, has position as it has a stop side to side to place it on the lid where the sensor goes.

I got a buick lacrosse 2010 with those codes it also keeps running when i turn the engine off like 5 seconds and the oil smells like gas could it be the high pressure pump the problem?

how much it costs to have timing chain replaced?

how much it cost to have timing chain replaced? is it even worth it?

Is this for working on the parking brake only or any brake work? Thanks

Great another awesome video. Garbage.

Do you by chance know the part number for the solenoid?

I have a Honda fit 2007 and the radiator fans aren’t working but they do turn on when I connect it directly to power and they also turn on when I go to the fuse box and touch the fuses with pliers could this mean the fuses went bad ?

What is this cause any damage over the long-term? Should I just put it in flood mode before I started in the mornings

Appreciate you brother ✊🏾

What brand of smoke machine do you have?

I just did this repair on Monday myself haha! I had no locks, and the reverse lights were on with lights off ,and off with lights on, and half lit with the fuse pulled. I had the ground and two power feeds broken.

Huh you change the odometer