วีดีโอ

What?

Try 1234, the programmer put password so no one can edit the program,sadly you cannot by pass it,the only way is to reprogram the panel and overwrite the program or flash the memory to return it to factory default panel all data will be erase.

Check loop resistance,it may be shorted or the loop needs to be check tru software and reprogram

I checked devices one by one and continuing test too.but there is no short Circuit

Sometimes after reset,it work normal but after sometime it shows loop fire

@sabiransari-yl8hd you need to check the connection for tamper switch in loop it might be the cause or some additional device attached to loop not programmed or defective. Or change the loop card temporary it migh be defective

Sorry its not free, feel free to email me at markgestadavid@gmail.com,thanks

Make sure the connection and wiring has no issues

to monitor the system

You need the software, email me for details. Markgesta@outlook.ph

Sent me an email

I need you to program me for the Watcher device and the mobile number

Email me to markgestadavid@yahoo.com

they block the audio, Lol

You need to reprogram and upload it to the panel or check the loop card if damage,the loop wiring if properly connected or no short circuit. You need to check the fault what it is giving you to make sure

@@markgestadavid u mean inject the same programe i have to the panel ?!

@Gostavo Mostafa if the panel has no problem before you remove to its original place ,then you should have no problem,but as you said faults came,then you need to check your wiring connection and everything.if faults still exist you really need to reprogram the panel accordingly to remove faults as a new commissioning panel to remove faults.

@@markgestadavid ok thank you i will try that Other question i have tools 8000 v1.19 and i want a higher update how can i get that ?

Get what? Email me

Email me.

@@markgestadavid mail id

@@markgestadavid ur mail id pls

Markgestadavid@gmail.com

You need to buy the resistor with diode. It comes with the box when you buy the panel

@@markgestadavid yes.I put the connection terminal with sounder circuit but trouble not clear

It is possible the mother board fault?

If its correct then try to reprogram the panel

@@engmuthu5663 if you did all the possible way

Check your software,driver and panel

@@markgestadavid sir USP to TTL software also need

i have three panel all panel not connect to pc please sir give me guide

@@சற்றுபாருங்கள் if you need software,email me at markgestadavid@gmail.com

Morley AIS

You need to change or check the device.it has problem.and you need to wiring recognize the loop again to remove it

Email me at markgestadavid@gmail.com

for EOL sounder resistor is 6.8k ohm

@@markgestadavid is that EOL are same size for ZX series ? Or only for ZX5se?

@@kevinseroy258 the same

@@markgestadavid Ok. Thanks a lot for your information 🙏

Technically no, but you can do conventional mcp with addressable IO module if you really want. It will just be expensive.

You can assign it in sector, either you put a resistor to trigger the fault or program it

If it is protected by code the only way is to flash the cpu of the panel to restore it to factory settings and reprogram it all over again

Need mo alisin and device sa loop at base para magtuloy ang loop wire

@@markgestadavid pag inalis ung devive automatic by na un sir

@@jkabayan105 hindi, kailangan mo syang i wiring recognize at mai program ang panel, pag na overwrite na ang panel at maisend mo ang program na wala na ang device dun palang magiging successfull, means mawawala ang fault sa panel. check mo pa ibang video ko para magka idea ka pa, thanks. dont forget to subscribe.

@@markgestadavid cge sir salamat

Nabubura? Di ko pa na encounter ang ganyan, pero wala sa software ung capability na byrahin nya ang mga naisave mo na mga devices unless nagdetect ka at nagoverwrite ng mga devices at naisave mo.

Nag ppractice palang po kase aq sir. Pero d pa ako nakakatry na meron na panel. Nakakapag encode ako pag ppasok aq sa projected devices after nun malilipat sya ng all bus device detector zone at zone control. Kaya pag inalis ko po yong naka save n projected device yong lahat ng na encode ko na bubura

Qatar po ba kayo sir

@@jaymarcrulona4253 sorry canada ako,anyway di kopa ginagawa yng ganyan kasi onsite at actual devices ang nireregister ko sa mismong software pag nag wiring recognition ako para buo ang loop at devices para.wala ako problemang fault na papasok sa panel

You can email me at markgestadavid@gmail.com