วีดีโอ

Ok thanks. Support me🙏🙏🙏

Ok fine but very very little much and wheel point enough.

Ons you contact any watch maker and ask you will defenetly get. Thanks

thank you sir.

thank you sir pls support me

thank you sir.

My pleasure!

Pls support me🙏🙏

I'm from India Karnataka state Mysore dist

Ok thanks🙏🙏

Ok sir i will try pls subscribe my channel sir

Thanks a lot🙏

All the best🙏

Most welcome sir🙏🙏🙏

Vintage watches are modren revalutionary watches

@@yogeshaar7386 no like are they durable I’m in 12th grade right now and usaaly wear Ricoh or Vijay is Omar good for such commuting

Dials are not fully clean by using any solution are brushing its handle very carefull and fix as it is.

Mysore Sir. Thanks for watching the video pls support me 🙏

Thanks 🙏 pls support me like this

You are welcome!

Thank you very much sir pls support and like me sir🙏🙏🙏

Because of there is no its screw that is why little bit fevi gum placed to stic Thanks for your comments pls follow me and suggest me like this🙏🙏🙏🙏🙏

There is no Dial nails also so i do it same way

Next time oiling the jewels also and ware gloves

Many many thanks for you pls support me like this

You are welcome! thanks for your compliments

It is soup water

It is soup water

@@yogeshaar7386 ok

yes i will thanks

It is 2030

It is 2030

Petrol sir

@@yogeshaar7386 Thank you sir

Thanks for your advise Pls support me like this🙏🙏🙏🙏

🙏 pls support me like this

@@yogeshaar7386 The gears that drives the hands of the clock or watch works in the same way both in spring driven and quartz clock or watch but in spring driven watch the energy stored in the coiled mainspring barrel is forwarded to the escapement and reversed back to the mainspring barrel repeatedly to keep the pendulum or balance wheel oscillating and then the power is passed to the gears in centre of the clock or watch to drive the hands. The escape gear turns once per second to both drive the entire gear train and to activate leaver escapement. In quartz clock or watch the mainspring barrel is replaced by battery and the leaver escapement is replaced by small peizo electric motor driven by small electronic circuit board of resistors that controls the flow of direct current 1.5 volts and gradually passes to small tuning fork shaped quartz crystal oscillator sealed in small cylindrical metal container that vibrates at the frequency of 32,768 Hz and the frequency is reduced by 15 flip flops in which each flip flop is 2 transistors kept crossing each other and the 1 Hz electric pulse is passed to solenoid coil wound over a tuning fork shaped soft iron piece between whose prongs a small pinion with magnet in it's base called rotor sprocket is placed. So that the escape wheel driven by the motor only drives the entire gear train.

@@yogeshaar7386 Please upload a video that explains how does hourly musical striking quartz clock moments and quarter hour striking quartz clock moments function. Do the same PCB board that consists of resistors that controls the flow of power from battery and pass gradually, tuning fork shaped quartz crystal oscillator sealed in small cylindrical metal container that receives power from the resistors and vibrates at the frequency of 32,768 Hz, 15 flip flops (each flip flop is 2 transistors kept crossing each other), microprocessor chip that receives 1 Hz electric pulse from the flip flops and tuning fork shaped electro magnet with rotor sprocket (solenoid coil wound over the tuning fork shaped soft iron piece in between whose prongs a small pinion with a permanent magnet in it's base) contains sound chips in which 12 different melodies with each melody followed by sounding the number of hours recorded and programmed and connected to speaker in it in hourly musical quartz clock moments?

By experiance, interest and consentration needs for work Thanks🙏🙏

yes i will do it pls

Thanks for the visit

Thanks pls support me like this🙏🙏🙏

@@yogeshaar7386 Please upload a video that explains the difference between the arrangement of gears in watch with centre second and without centre second hand.

pls share me if any information

thanks pls support me

@@yogeshaar7386 The 60 : 12 : 1 gear train that drives the hands of the watch functions in the same way in both spring driven and quartz watches but the great wheel that carries the mainspring barrel is replaced by battery and lever escapement and balance wheel are replaced by small peizo electric motor which consists of PCB board with resistors, tuning fork shaped quartz crystal oscillator sealed in small cylindrical metal container, 15 flip flops (each flip flop is 2 transistors kept crossing each other), microprocessor chip, solenoid coil wound over tuning fork shaped soft iron piece and rotor sprocket (small pinion with magnet in it's base kept in between the soft iron prongs). In spring driven watch when we wind up the mainspring by the crown it causes forwarding and reversing the power from mainspring barrel to escapement repeatedly and causes the escapement to push the balance wheel forward everytime it return backward to keep it oscillating for days because as a result it drives the hands of the watch forward. In quartz watch battery powers the peizo electric motor which drives the gears that drives the hands of the clock.

Govt iti Saligrama

date and day watch is more expensiv

@@yogeshaar7386 Thank you!

In Mysore

Care should be taken to insert Wheel point in a jewels and align properly

Thank you very much.Keep Supporting🙏

@@yogeshaar7386 Please upload a video that shows what electronic circuit is there in some quartz clocks that electronically reproduces the sound of marking every quarter hour by 1/4, 2/4, 3/4 and 4/4 of the musical sequence of Westminster, Whittington's, St. Michael's or Schubert's Ave Maria chime melody on 4 to 12 bells of different sizes in addition with counting the number of hours as chord strokes on 2 or more bells (striking simultaneously on 2 or more bells). Are such quarter chime sequences with hour strike sound recorded and programmed in the same PCB board that gives one second electric pulse to the lavet stepping motor or programmed in separate circuit board and connected to the PCB board that gives signal for every second to the lavet stepping motor?

Thank you very much.Keep supporting🙏

Thank you sir🙏

Light oiling necessory or it may skip