วีดีโอ

Sick!

What kind of oil did you use.

Dude, please drop the part number for that spark plug socket from Honda. I have managed to change 3 of the 4 on my 03 750, and not socket I get to go in there works. If I can get 1 socket for all 4, that would be AWESOME

I’m having trouble with the front bolt blocking the seat sliding in the front. Any advice?

The tool I bought is just like your but seem too be too thick ……do they make different one like that

Your oil looks milky

could you do a video on how to change the oil filter?

Is that a Honda and Mitsubishi tattoo lol?!

I have the same exact model Takes synthetic non detergent air compressor oil and about 16.5-17 oz. I was looking for a 20oz or a 40 oz that way i can do 1 or 2 oil change but HD and CT only sells them in 32 oz containers.

Stupidest video I've ever seen. U didn't actually show how to remove. Da.

i needed know how put it back together last parts.. u didnt install : = no thumbs

I bought a 2022 Honda trx90x and I did the initial oil change at 3 fuel tanks or 2 in a half months that also implies for the CRF 110. I think it better because your letting the engine fully break in the motor and the clutches

Can u sit it on its side like that won't the... acid leak out?

I'm sure I'm just being paranoid but... I have a 2019 crf110 and it shakes when at idle. I have a crf50 and crf3001 and they're smooth as butter. Any chance yours shakes / feel it in the grips when riding or at idle? From the looks of yours, I see a similar shake.

Nice Mitsu tattoo

Can you share where to find that removal tool you used at 3:45

Great video. I have this exact bike and looking to change the oil. If you know the size of the plug and the size of the crush washer please let us know. I've watched dozens of videos and searched the Internet and can't for the life of me find this information. I want to buy a magnetic plug and new crush washers, and the only mention of sizes is on ebay (M12x1.5?), which I don't trust. I hate to have to drive to my local Honda dealer to get such simple parts but without knowing the size I may have to. Thanks

Gr8 work

How much oil does it hold once you've removed the old oil?

Tip, use some rubber lubricant (or soap) on your tire and rim beads. This will prevent bead hang-up, and possible air loss. Just don’t use petroleum based grease or oil, because they will damage your tire beads. The study 📖 is also inconclusive on food 🥘 based grease or oil (my own studies, I haven’t tried them). Clean 🧼 water 💧 is okay (preferably soapy clean water). Your friend, Jeff.

It would be a whole heck of a lot easier to use a chisel under the rim bead, hit the handle with a hammer 🔨, and go around the rim while doing so. I watched a friend do this with my 3 wheeler tire 🛞. It took less than 5 minutes. Your friend, Jeff.

Learned about crush nuts. So very helpful video.

The thumbnail freaked me out, I thought it was creepy eye lmao

So what was the intermittent spark issue?

yes pour some soap or wd 40, I just did 2. lube and lots of prying and hammeroing on the tire

Thank you for showing how to change the oil, your video helped us out.

Wish mine would come off this easy.

Very nice It idles U did well

Whered you find the passenger back rest?

Terrible video

LUBE!! USE LUBE when mounting a tire on a rim!! And you should've cleaned the rust off the inside of the rim and painted it. That rust could and will cause leaks sooner or later.

Muriatic/hydrochloric acid (aka brick acid) is superb for carb cleaning. It cannot harm brass but can dissolve aluminium castings so experiment with diluted acid.

The legend has returned.

ayyyyyyy!

У меня чорный дим пачему ричиа кто знает

picked up 1985 200S ATC , do you know if front rim is 1 or 2 piece? thx

picked up a 1985 200S ATC. Do you know if front is a split wheel or single? Thx

This is cleaning of fuel chambers only. There is lots more to do. Choke, pilot screws, rubber membranes, slides and more. Float level is not adjustable in this model. One thing less to sorry about. Waiting for part 2.

FML. I had the battery upright and not lying on its side. No wonder it didn't fit.

it amazes me how these things weld themselves to the rim. i spray with wd40 before starting. it works, not easy. but much easier.

I wonder does soaking damage the rubber part of float valve ?

once the oil is drained, screw in a 4 inch pipe with a valve at the end. Next time it will be way easier.

A split rim without a tube. Is that an o ring at the 4:05 mark?

Arisol glass cleaner makes rubber super slippery for seating the bead

I'm doing a build on the same exact model. I was wondering if you've tried a Mikuni VM22 carb on it?

Where did you get the O rings

Why not use a bead sealer like " Murphys " Right before airing the tire up. It would have seated the first time with a little lubricant. Making a video installing a 2 piece wheel is very dangerous and should not be done like that ! Especially dry.. Oh and buy the way your supposed to have backing plates on that kind of wheel !

Dropped my 74 Honda 125 Scrambler in a puddle of water today and now she's not idling well. Seems to be getting great spark and runs fine at high rmp, but will not idle. Guess I better take the carb off and see if anything is wrong in there.

Not sure what your doing other than making it look easy.

Can you help me to set up the rigth height on the floats that's the only thing I need to know thanks