- 8
- 4 838
Spanners and sparks
United Kingdom
เข้าร่วมเมื่อ 16 มี.ค. 2020
I seem to have accumulated a few motorcycles over the years. (Mostly red it seems)
All of which compete for my attention. So in my cramped little lock-up I keep on top of maintenance and muddle through with a set of screwdrivers in hand and a little bit of knowledge here and there. It keeps me out of mischief when there's no tango dancing to be done!
All of which compete for my attention. So in my cramped little lock-up I keep on top of maintenance and muddle through with a set of screwdrivers in hand and a little bit of knowledge here and there. It keeps me out of mischief when there's no tango dancing to be done!
Villiers Mk25 engine strip and restoration
In this short video diary, I make my first attempt at fixing an old side valve engine from a Wrigley's cart. The engineering is simple but effective and I find working on this engine from a by-gone era to be absolutely charming. From the beautiful brass fittings and the use of simple design, making it a real pleasure to take a spanner to.
A few mistakes along the way, but no real issues to contend with.
I hope you enjoy the video.
A few mistakes along the way, but no real issues to contend with.
I hope you enjoy the video.
มุมมอง: 860
วีดีโอ
Suzuki TS185 M Rebuild (1976): Oil feed pipes (removal, replacement & bleeding)
มุมมอง 1Kปีที่แล้ว
In this video, I remove old oil feed pipes and find one faulty non-return valve. I then bleed and test replacements, before refitting to pump and engine.
Suzuki TS185 M (1976) Rebuild: part 2- refitting piston and cylinder
มุมมอง 370ปีที่แล้ว
A simple rebuild showing the refitting of piston to con-rod and lining up rings to fit the cylinder and tighten down the head.
Suzuki TS185 M (1976) Rebuild: part 1- preparation
มุมมอง 539ปีที่แล้ว
Engine has sat in storage and needs recommissioning before rebuilding bike for the Spring Part 1- Draining oil and removal of cylinder to assess condition and wear.
Kle500 spot light refit
มุมมอง 53ปีที่แล้ว
In this video I refit my LED spotlights for the winter. I bought them cheap from ebay and after using a little sealant to keep out moisture have been surprised at how they have performed over the last 2 years. A simple set up with a fuse, universal relay & wiring block connector. It makes a big improvement to night riding and day time visibility
Leaking coolant pipe Kawasaki ZX10- part 2 (install & reassembly)
มุมมอง 137ปีที่แล้ว
Part 2 of 2- installing cylinder block coolant outlet pipe and reassembly of cooling system, carburetors and airbox on 1989 Kawasaki ZX10. This is just me doing what I do and not intended as a tutorial (Though may be useful to owners of similar bikes)
leaking coolant pipe Kawasaki zx10 (part 1- strip down)
มุมมอง 335ปีที่แล้ว
Replacing a leaking seal on metal coolant pipe of an old ZX10. In this video I remove carbs without disconnecting throttle cables, and leaving top section of air-box still attached for easier reassembly. Not the best quality video as it was filmed on mobile. This is just me doing what I do and not a tutorial. I mumble a fair bit too :-)
E-bike battery (silverfish) - fitting the mounting plate and slider
มุมมอง 1.5K4 ปีที่แล้ว
Fitting replacement Lithium battery to old folding bike, as original Ni-mh battery was fading. Time to upgrade and fabricate mounts for silverfish type battery
I have the same engine type which needs some TLC. Where did you find a parts manual? I have looked on internet without success. Thanks.
www.lsengineers.co.uk/villiers-mk25-engine-spares.html Here are some other sites I found useful: www.smokstak.com/forum/threads/villiers-mk25-setting-gap.162852/ www.villiersservices.co.uk
I have a basic pdf. service manual if you want.
This was helpful too as this engine used on some of these trucks: facebook.com/groups/1636560479946601
@@stewartwells87 Many thanks for the info. I think I'm OK for the moment but I may come back to you if I get stuck.
Fascinating
What panniers and topbox on this please ? Also what bracket for the topbox ?
I think you need a new camera man, tried to understand but impossible angles