วีดีโอ

Sir, there are few methods to reduce the noise. 1. Air Intake Filter: Please check this filter. If the air filter is ok then 2. Head ( Motor ) : Please change the compressor Head ( Motor ). If your Compressor has been running for the last 3 years then I recommend changing the motor head. Or 3. Install the compressor Away from the procedure room. or outside of the Dental chair room. Connect the air by Piping. Thank you so much sir for your inquiry.

Please follow the following steps: There are two Pressure gauze in the Compressor. 1. pressure Gauze ( Large) : it measures the Air Inside / inner / compressor tank Air Pressure. Cut out pressure ( Auto Stop point : 8 bar and Cut In ( Aut Start point): 4 bar. Please check this phenomenon first. 2. Sometimes the compressor stops running before 4 or 5 bars. At that time please check the Electricity Power supply voltage. 3. If the above two methods/points are ok, But Tanky pressure is not increasing above 5 bar, Head motor is continuously running. Then Change the Compressor motor head. 4. If the compressor motor stops when Tank pressure Gauze needle is reached to 5 or less than it. Then adjust the Auto cut system ( Small black box ) to increase the tank pressure. There is another Pressure Gauze ( Small) with Moisture Trapper: 1. Maximum Pressure we can deliver to chair is 6 bar. The Dental chair pipe pressure capacity can hold this pressure. We can adjust from its adjuster given to the top. Thank you.

Gracias 🎉

Please Tell me Which PCB you replaced.

2,30,000/- Bestodent Aqua with Inbuilt Scalar.

Small pipe ( White Transparent ) for Compressor Blue pipe for Water connection

@@kanhaiyalalgaud567 i could not understand what you want to say.

2,10,000/- + Transportation charge extra

Excellent and better than others.

Ocean Green Colour

@@ALLINONE-it5ch Confident is the best with all features in one chair.

@@ALLINONE-it5ch Confident Mokambika / Confident Meenakshi

@@erkrishnakumarshrestha I like Meenaksi dental xhair design

@@erkrishnakumarshrestha For single hand use Plz suggest one from orikam vatech woodpecker And best Rvg also Nano pix Vatech Carestream woodpecker Xpectvision

@@erkrishnakumarshrestha Sir for single hand use Plz suggest one from orikam vatech woodpecker And best Rvg also Nano pix Vatech Carestream woodpecker Xpectvision

Your location please

@@erkrishnakumarshrestha phone number dinus na...im from imadol,lalitpur

@@erkrishnakumarshrestha im from gaushala sir...can i get your contact number??

@@nostalgicsouvenir Mokambika Dental Chair, Meenakshi Dental Chair, Chamundi Dental Chair.

@@erkrishnakumarshrestha chinese ni ??

@@nostalgicsouvenir Zoinchamp: A-200/ A-300

@@WillemGeant-p6v yes sir. Of course. +977- 9851142296 ( Nepal) / Email: erkks2041@gmail.com

@@RabindraThakur-g8e 9851142296

I will upload the next video.

It was due to the oxygen purity sensor expired. In this case We should replace the same type ( original) of the Oxygen purity sensor. After that this problem will be fixed.

Pls ba ta yen

@@kanhaiyalalgaud567Sorry, i did not understand what you want to say. Please tell me clearly. Thank you.

Currently the same as this, Runyes Company comes at NPR 1,65,000/- in Nepal.

00977- 9851142296

​@@erkrishnakumarshresthahello my chair is confident Mookambika can you help? The up and down movement is not working... What do you think could be the issue? As I've changed the PCB also... The back and front movement is working fine...

@@rakibhussain521 00977-9855080448

@@Guiding100 Mine also same problem with in 2yr of installation of confident dental chair ,chair go up sometimes gets stucks on moving up,doesn't cum down later patients armrest gets broken and also hand piece holders also Company doesn't service it and tells to replace for new1 after taken 2lakhs for this chair when other companies actuators and pcbs is of low cost still and good as well

If so, Please follow these instructions : 1.) Disconnect the Head from X-ray arm. 2.) Check the resistance between Yellow and Blue wire of Head jack by using an ohm meter or multimeter in ohm mode. What value comes, please tell me. If the value ranges between 11k ohm - 15 k ohm, The head or cone must be ok. If ohm value does not show within the range, that means below or above the range means Cone or head is faulty. 3.) If Resistance shows between 11 k ohm-15k ohm, and then the power board needs to check or replace. or somewhere wire connection may have issues. might be disconnected. etc. Please inform me whatever.

May I know the duration of the X-ray machine you bought?

Ok sure. I will upload in English in the coming days.

I Could not understand your opinion.

Bestodent - AQUA: NPR 2.1 lakh Confident- mokambika : NPR 4.5 lakh

@@erkrishnakumarshrestha i am from India Besto Delite 1.5 lakh Mookambika 2 lakh

Bestodent delite costs 265K/- NPR. Transportation charges will be extra. Best is Meenakshi sir.

@@erkrishnakumarshrestha how much diffrence in quality of confident and bestodent ?

@@ALLINONE-it5ch both has motorize suction. But Confident has high quality LED light, Comes with inbuilt Light cure, micromotor, scalar. Easy to handle and also to repair by online video call instructions. It is better for surgical cases too. Durable than Delite. But Delite is also not so bad. It can do what a confident chair does. But we have to add extra features to it externally.

@@erkrishnakumarshrestha ok So confident is long lasting . Here in India i am getting almost same feature in besto delite also But dont know about suction motor quality and chair quality And only 50k price diffrence in mookambika model from delite so confused .