วีดีโอ

In the future use safety glasses when striking one hammer with another one, they are hardened and will fracture into sharp bits.

I don’t know if you noticed, but the original OEM axel that you took out had a counter balance around the shaft and the aftermarket shaft you installed didn’t have one. I mention this because I have learned on a 2014 C-RV that it will most likely never balance out and ride smooth if you don’t use an OEM balanced axel’s.

If pressure differential sensor is not unplugged and filter is pulled and replaced/cleaned does the sensor need to be recalibrated? Thanks

Those are some nice wheels! What were the symptoms of the bad axel? My 17' Si is shaking every 2 seconds while driving. Shaking is noticable at 65+ mph.

Hi i hav 2016 isuzu 800 pto light goes on but there no pto how can u help me lump mode

Thank you, you’ve helped me gain the confidence for the first time to do this to my 2018 SI

Now i can do my civic si passenger side axel with no worries

I have a Isuzu nrr with one of the lines is clogged is that causing my dpf issue

Thank you

The grappler tool can save time in many situations and is great if you don't have access to hydraulic press. However, on the car in this video, he was one nut away from having the whole knuckle off the car. At that point I would have just used the shop press.

Beautiful explanation of everything

Some bearing manufacturers (National) are now making the bearings with the ABS encoder on both sides of the bearing so you can't put it in wrong.

excellent informative video

This guy makes this so easy 👏👏👏

I have an easier way on a 2012 civic ex sedan, just take the 2 bolts from the strut and you can wiggle it out.

I did not know that about the dashboard! Still learning something new everyday

prolly the worst install ever- dude barely shows what he’s doing… if i wanted to listen to an audio book i would. This bout as useless as reading shit online. Doesnt show shit that he’s doing.

You probably should have taken the entire front clip off of the car to make it easier

Great video Preston

how about the link to the otc tool... thx

5 minute leak test what micron decay did u have in that 5 minutes decay test. just curious

Flawless tutorial!

Does this display in Spanish?

Hey all! Just did this job on my 2016 civic EX and the axle nut is 32mm instead of 36 on this Si.

Thank you for the detail that was put in this video. I will do exactly this repair soon due to the clunking noise.

Awesome car! Better Scan Tool!!

That's some great stuff!

anda punya banyak video bagus kenapa anda tidak mengganti nama chanel anda lebih familiar

Muchas gracias si los puede enviar en español le agradezco

Great Video! Thanks. I have 2012 civic with CV Boots issue. Shop recommended me to replace whole Axle Assembly.

Never had the ability to deal with degrees Seen the specs on DTNA freightliner specs all in degrees I’ve been doing mine with actual measurements in inches But then again I’m using lasers and a tape Measure

Nice !

Thank you very much,I'm working on my 2010 crosstour,I replace the starter but is the same,won't crank,do you have a idea what can be the cause?but thank you again,you explained as a professional👍

Will this program work for dirt bikes?

No issues with the pebbly substrate in the trans tunnel?

Thanks sir

Old video but when you took your measurements your rim diameter was saying 16.6 I thought you said It was an 18inch wheel ?

Pedders coilovers!!! Aren't they identical to BC racing coilovers?

Wheel hope will break anything

I have a question, is a wheel alignment needed after axle replacement?

I have a P2206 and P20c9. What is my best place to start .

Good job 👍

Thanks a lot for this video and making sure to show every important step! Is there any lubrication needed for any of these parts before installing the new axle or reinstalling the old parts?

Can i put a wrx turbo engine in to a 2011 outback?

cool stuff

If anyone can help, would this be the same on the driver side? I have an 18 Si Coupe and it needs a driver side CV axle.

Cant get the driver side off. Any tips or tricks?

Both Blue point and SP tools are made in Taiwan by Hi-Five tools SP is just using there newer model ... but neither are made in the USA and not one is better than the other ..Hi-Five even make the reversable ratchets for Blue point snap on Gearwrench Craftsman SP Jet and like 60 other companies

How may mile this car ?