วีดีโอ

i dont have a center hole in my mount. Am I SOL?

Video title: "fiber", text on device: "fibre" 😏

What if the whole entire wall is stone and there isn't any drywall? That's what I have in my house.

What a useless video

Why you don’t just anchor the mount nto the pillar ?

Can it go 180 to the oher side to

Do not use hiltys on marble.

Oh thank God for posting this! What size tv is that? How is it holding up?

It seems you did not mount to the stud? Just using the heavy duty drywall anchors?

In data centers they’d want the bundle to be cleaner. No diving cables

This is a good video, except there was no commentary during the process. I did not understand what was going on. The fact that you focused on behind the TV was a plus for you.

Garbage…..

Terima kasih... mantap videonya

It's like nine times easier if you put the bolts in the play bar and then the nuts on the other side

Thank you, I just wanted a simple video explaining this❤

The provided cable isn't rated for being behind the wall. You need a conduit

Hlo sir im from india i need a job i have 3 year experience of optical fiber.

This is by far the best video I’ve seen! So helpful, thank you

NA dude never seen a concrete wall in his whole life. Living in homes made of sticks and paper sheets in the country with most intense hurricanes and tornados.

Old metalsmith trick. Start the hole with about a 3/16in drill bit, it will punch through the thin stud metal much more quickly. Then go after it with the big bit. Go slow when drilling metal. People always want to just power it through. All that does is produce heat, and you will burn up your bit. If the bit changes color it is ruined. You have heated the temper out of the bit and made it too soft to cut through the metal. Might still be ok on wood or plastic, but never will cut metal again. If going through thicker metal, always start with about a 1/8in bit, use a bit of oil or WD40. Go slow. Move up to a 3/16in bit. More oil. Slow. Move up about 3 more sizes. Same thing. Until you get to the size hole you want. Takes a little longer but you won’t ruin your bits or your hands or run your drill batteries down too fast. If the oil is smoking, you are going too fast. And use a proper drill, not an impact wrench.

Very useful tip thank you very much

that looks like a good stud finder. I got the Bosch one and it's paying up. Sometimes two completely different reading and only show centre of the "stud". Is it best to drill above to see if you are on the stud

The tilt down in the example image is not advisable when the height is correct.

Try not to fiddle to much with it around the hole. The tip is very sensitive. Avoid touching it yourself or touching it with the side of the hole. If you scratch it or the grease will deposit on it from your fingers then the signal laser will be deviated resulting in bad signals.

Couldn't believe I found this video. We had the TV mounted for us and I wasn't familiar with the mounting mechanism. Thank you so much for this!

I have one tv in living room fixed to steel studs. But in the bedroom opposite of the living room, im putting in a tv, only one steel stud will be common to both sets. Will that stud be able to handle it?

Sounds like Thomas the tech that was suspended for being unsafe on this install

How is this a concrete wall? Looks like cardboard to me

Is Fiber available in Laval?

Beautiful! Wondering what the cost is

I was patiently waiting for pros or cons about the Bell Wifi Pods........................... but I didn't hear Bell mentioned. Hmmmmmm.

Question is this procedure put in all the rooms, as I have a tv in my bedroom too, or just the living room?

So helpful! Worked a treat. Thank you!

Sloppy asl

We have tested both and have two other videos to explain that. This video is about the access point installed. i want to see the other two videos

I have my hole started but can't seem to penetrate through the marble wall with my tile bit, what should I do?

Warning!!! Never remove the plastic in the Wall behind plaster if it is a outerwall. The plastic has the purpose of beeing a diffusion barrier preventing the moister from the indoor climate going to the colder wall. You will get mold in the insulation and the Wall if you make a tiny hole in the diffusion barrier.

Shite 💩

Nope. No idea whats going on here

Kalau sering” d lpas pasang aman aj kh

For that I should get wired cameras 😂😂😂

Could this work for a swivel mount on a 65” tv

Do you add a flame to the end to prevent fraying?

Ok, those look like some seriously good scissors!

Thanks

U guys make it in white? Where i never saw it in white..

Concrete wall will not have a cavity behind.

Is it possible to do this in concrete?

I dont think you could have found music that fit any worse lol

ZeboZAP is the best gazebo tv mount