วีดีโอ

Excellent!

Mine lasted around 700 -800hrs before I had to replace them on my kubota

Reds clears on front

we dont say "chinese garbage" but just "made in china" !

I have a radio (SKU: JY-HQ123N4G) JOYING Android 10.0 and I have a problem with the mic when I talk on the phone, it sounds low. Could you tell me how to get to the mic setting and be able to upload it more. I also tried with the external mic and still the same... thanks

unbelievable Machine .. I need one for a Narrow Trench for pipe .

What type of Briggs and Stratton engine is that?

Make sure its not rigid... There needs to be movement and a bit of flex. Remember that your taking from the high and distributing it into the valleys.

congratulations on the v8, discontinued now.

The Toyota hitch has a anti rattle bolt underneath so you shouldn't have any problem with the pin

How long did you wait for yours to arrive?

Crap. I just rebuilt 2 of these yesterday and I wish I had seen this video first. I would have definitely done your zirc mod. Sealed bearings are designed obsolesense. They shortly run dry and fail. I have only 260 hours on my Z-421 and the center spindle bearing failed fully with the right side just barely showing early signs of failure so I did them both. The left side was fine. No play or noise on hand spinning it. Good mod. In the future, I'll do this. The only thing I can see it could do is dislodge the grease/dirt shield you left on the outside of the bearing but if you are careful to not over grease, it should be fine. Like you say, the grease will with use, find a way out. Adding back a pump or two at blade sharpening and deck clean out should give the bearings a much longer life. So, it's been 2 years. How did it work out? Tip for others out there in TH-cam land... to check your spindle bearings, lift the front of your machine how ever you do that, release the belt from one blade pulley so the belt tension is off the system. Go under, grab the tip of each of the blades and wiggle up and down. There should be zero play or movement. It should spin freely and easy with no noise. If you can wiggle it up and down, or they bind and or make any noise, your bearings are failing. There is another Kobota zero turn video on TH-cam, and his center spindle bearings failed at 160 hours. So apparently, this is an issue. Like I say mine, failed at 260 hours. So get ready. Also unless you have been running failed bearings, you won't need the spacer or shaft they will try to sell you. Just the bearings. Obviously, take yours apart first to assess your needs before ordering. My housings, spacers and shafts were all fine. If you are into factory torques... Blade bolt- 85 foot pounds. Spindle pulley nut- 120 foot pounds, the 4 spindle to deck nuts- 60 foot pounds, all per the Kobota service manual. Enjoy!

Clever idea.

This is the best way over hiring scaffoldings. Well done mate!

Something like that would be perfect for digging tunnels in the backyard

By drilling a small "weep hole" on the other side of your spindle you'll be able to tell when you have pumped enough grease into the spindle and avoid over-filling with grease.

What a top idea, looks good 👍

been fighting one on my 135.....I debated this last night so glad I know it works now.

Bloody brilliant and if the client doesn’t like it, the client is an idiot!😂 Honestly the mock up looks amazing. Using galvanized steel is a bit overkill because the first deep scratch into the paint will cause corrosion regardless. Love the work and absolutely stunning!

Looks unreal!!

Looking good🙌

i have watched countless spindle videos .and there seems to be a coulpe diffrent camps of thought.if you take a sealed bearing apart the bearings are in a cage and the cage and bearings spin together. some say if you pack them full it couses more friction and makes them over heat.whitch makes sense.they say only use about 25 percent of capacity of the bearing take the factory grease out and use high temp good quality grease. i dont know zerk or no zerk .

Nice video mate! Just wondering if you had any dramas getting the kit? Did it take long to arrive?

how much did you pay

Good job.. I have done the same… what is the brand of your drill press vise..I like that

Hey mate I’ve noticed in the comments you’ve said you’ve bought a module to make the indicators flash? I’ve got the same kit installed and want to do the same if you could point me in the right direction? Cheers for the video too it helped heaps 👍🏻👍🏻

Thanks for the simple fix. Good troubleshooting!

Excellent, but I think this one's smaller 😂 : th-cam.com/users/shortsb4HqeW8_X7I?si=DX5qS6A0p_o95w2r

What a cute machine. When you need to dig inside a basement it will fit thru the doorway. And you can pick it up and put it in the back of your car 🙂

Thats a cool spoon with an engine!

How much did you pay for it?

Great video. Are u planning to do electric windows ?. Ive seen a guy in Melbourne sell single cab door cards ect but no dual cab options. Waiting / trying to work out the best way

Red Loctite 271 in a grease fitting 24 hr. cure Pre grease prior to install and grease every season. Caution new mower spindle assemblies! DO NOT install mower spindle without a new drilled tapped red loctite in a grease fitting installed. Nice On of the best TH-cam videos out there Thx

0:18 Riker Maneuver

My Kubota K008-3 weighs in at 997kilos! That thing is a lot smaller. What a cool little rig. I had looked for a small one like that, but never found one of those in the US.

Where did you buy that and how much

Any update on it? Are they worth the money?

I could be wrong, but when you were digging, isnt the extended foot supposed to be in the back and not in the front?

mmm, those covers are on the bearings to keep dust and dirt out. you meesed up

love the actual work. the audio sounds like getting a root canal. maybe some music over the metal grinding.

Nice!

Good video mate, going to do this to my workmate, I think your wrong about getting a gxl, was recently offered a gxl 2023 facelift v8 by a dealer and I’m not even on the list just enquired and they said it’s coming in this month.

Add that bit of chain back on as a link between your mower and tow point. The front is lifting up because of the angle to the mower.

Good idea buddy. I have done similar. When ya need a piece you need it now. Especially if its keeping you from getting a check. Keep up the good work.

Is this turbo model

I just bought same one, where did you get stereo?

Awesome video mate cheers for taking the time to upload, i welded some short pieces of rebar on mine so i could put old gym weights on there ( gravel driveway ) works a treat. my cutting edge is a little lower because of the driveway and im going to make another smaller one like yours for the lawn area, cheers again for the video, Perth Western Australia

The little stick is the 4 wheel drive then puts it back in low range or 2 wheel drive when he's upto speed

the cutting edges need to be a little lower than the skis

Tried to find the blades. I got the same mower... I added the grease fittings to mine but I'd like the blades