วีดีโอ

I appreciate u sharing this thank u so much.

Clutch

Great Work

Brand new cable gets so jammed and you can’t even pull on it. It’s just a nightmare, the wind rope that I broke was from Amazon hundred bucks later junk, but the original Canam rope for $180 that didn’t last much longer when I was pushing some dirt around, I snap that too. They’re not made for hard work it seems.

What happens if this sake thing happens, extract bolt. Replace bolt. Have vacuum at pump again but still a hard pedal, ok until used once or twice then goes hard again. Let idle brake is good, use brakes loose pedal

Just did a three piece one 2007 edge and pain in the butt

I have a 2010 Mazda CX9 which are supposedly the same vehicle as the ford edge. Mine has a 3 piece drive shaft with 2 hangar bearings. They do sell the bearings seperately but after not finding anyone online that has actually done a 3 piece shaft bearing replacement and reading the reviews on amazon, it seems that the 3 piece shafts do not come apart like the 2 piece shaft does. I ended up ordering the whole shaft assembly with the 2 hangar bearings and all new u-joints for $250 from ebay. I know it's more expensive then just replacing the center bearings but you get the benefit of getting an entirely new assembly. You also get the benefit of an easier job. If you try and buy the entire shaft from some place like advance auto, they want upwards of $800 for the part. Hopefully the shaft is well balanced as well as the OEM shaft was.

😮

408

How long did you run that motor after the shaft replacement? Any issues with debris? I just did this myself and obviously nervous about any debris that might be left behind.

Note that the spline has one groove that is wider than the others. It will go together only one way. I think you can see this in the video at time 9:37. This is for proper balance. You should mark both sides of the shaft before you separate it just in case your spines aren't like this so you can put it back together the same way.

About how much would a job like that cost?

You forgot to show how to get the pump lever positioned correctly on the cam. I have only ever did a 360 and a Chevy 307 back in the early 90s so looking for help.Your motor sounds bad ???????????? If I had noticed the Eastman sticker I would have passed this up. I will give you a thumps up anyway and find out how to position the lever.

How did you fix that part that broke off in the cam?That just happened to us.

How did you fix that part that broke off? That just happened to us.

How did you fix the part that broke off

Do you have anything on this carberator like a rebuild or diagram

I call it suspended animation

Me & my ‘79 Lincoln Mark V coupe (19.5-ft long) agree with your art statement.

Just did mine but i had a major oil leak no vaccum problems.. Fairly easy fix! I got a deal on the car i bet they thought they needed a head gasket... its around the same area!

You sell your pick up yet?

What price is it

Do you have a radiator for Honda CRX

I've ran into a lot of trouble,... with the replacement pump's (Carter... china one's),... had 3 of them on.. in 6 months,... new front and rear tanks.. sending units.. lines,.... everything,... theres gotta be a better mechanical pump out there........

Can you send me the link for that kit

That is neat! Don't forget the cup holders and fone chargers.

That looks like it'll be a lot of fun, cool!

Just a heads up, don’t use a step bit when installing the visor on the cab of your truck unless you remove the headliner. You’ll end up with two holes. One on the outside and one on the inside. Use the proper side of bit with a drill stop on the bit. Just me talking out loud 😉

Haven't had issues yet so I like them

Awesome thank you so much! Helped me replace the gasket in my vacuum pump :)

Fabulous! Does the bus have a nickname? For the next shop class I have a Corolla that needs a new/repaired transmission. Come to think of it, one of those Utica students destroyed it on the way to soccer practice.

Just using the proper sized drill bit would save all that waisted time with the step bit. 🤦‍♂️😂

Gibson is a beautiful pup!

😊😊

Thanks, bro! really needed this. one of my lines broke on my exact same model of vehicle except blue. this'll really come in handy later. Thanks again man!

Thanks

👍🏼👍🏼👍🏼👍🏼👍🏼

Could do without the music

Nice!

How did that budget coil perform? Did it last more than a couple months? Keep hearing everyone saying to only use OEM VW coils or they either wont work correctly or will short out in a short period of time.

How has this set up worked? I want to do this on my 351M in a Ranchero and have others telling me I can't eliminate that box????

Man how I miss commuting to work in the snow, it was awesome, especially when the roads are empty...lol

Wished we had this in Georgia

You didn't say where the lever goes ( on top or below the camshaft ) 😰

Air cleaner is not big enough for a lawn mower...

Very informative. Thank you.

What model Ford Edge was this? (Sport, Limited, Sel)

Good deal forsure

what was the part number for the bearing

Can I use the battery in my Ford rustang