วีดีโอ

How to replace oxygen sensor?

Youre amazing, thank you!

Appreciated. Alas, our silencer doesn't appear to extend as far out as yours so the bracket would have to sit beyond the silencer. Probably have to cut the studs off and use to self tapping bolts to position the bracket further along the chassis.

Turn wiper on and turn car off so they are stuck up. Now to see if I bought the right blades but I’m not feeling it

Thanks for a great video , it made it so much easier to do . I used a 13mm box spanner which was easier than a socket . Had to replace quite a few of the stupid clips and when I was putting the window switch back in it fell apart as the plastic was so brittle . Aah well that’s easy to replace when I get one

👍🥂

Io ho utilizzato una fascetta tipo stringitubo della giusta lunghezza

The bulb with the metal clip that you remove at 3:40 is the main beam, the sidelight bulb is to the side of that below the indicator bulb.

Numberplate bulbs counts as exterior I'll say!?

You should loosen and tighten the wheel bolts while the wheel is on the ground, then the car is less likely to fall off the jack

you missed the important bits

Excellent video, many thanks. Is it easy to change the middle coloured section of the door mirror if it is necessary to buy one with a different colour?

Well made video! Thank you

i always slightly loosen the nuts on the wheel before you raise the car ,its much safer and easier 👍

What do PD mean

Excellent. Very clear and easy to follow. Thanks.

Cheers pal..saved me a huge problem.

Thanks, very entertaining and just what I needed.

Hi this was exactly what I was looking for, please can you send a link...

Hi, Thanks for this brilliant video. What size is the spark plug removing tool? Thanks, Kind regards, FV

You lowered and raised the car on the manufacturers "side of the road" jack. Next time, read the instructions on the jack. NEVER NEVER use that jack to work on a vehicle. My arms, fingers and feet are too important for your methods, thank you

Thank you for this tutorial. It has been usefull .

Thanks!!!

Nice video with very clear explanations

Nice one 🙂

Спасибо большое за информацию очень наглядно.

ok so the title is a blatant outright lie because you changed nothing, all you did was put something over the mirror.

Thanks so much for this video tutorial. One question: Can I use the gun of my air compressor to clean the site where is the old filter before inserting the new one?

Number plate bulbs?

Front part is cat

Thanks for video if anyone hears water when they turn a corner they say to check this as well 👍🏾

I own a 1.6 vtr vti Picasso and I use a green washable air filter.

Great video, thanks!👍

My Citroen blades not like this.

Thanks for this .... What about the rear numberplate lights?

Came across your channel thanks for the info sub from me aswell not many videos on this modal as I have a 2010 1.6 exclusive hdi

Manny. Thanks

Thanks, simple great video:)

Great stuff, helped me 💯

Just done mine I couldn't see the point of the long pin I cut mine off my new mirror so I could get the socket to fit

A lot of help

Great instructions really helpful thank you for the tips

Good thanks

Love all your videos, hope your well. Haven’t had any new videos uploaded recently. All the best in health bud.

Hi, I have a c3 1.6, petrol it’s exactly the same engine to look at, my problem is I can not for the life of me locate the fuel filter. I work in a bus garage and none of the mechanics seem to know where it is. Watched a few videos on TH-cam but I have nothing where theirs is located. Do you have any ideas or could it just not have one.

not usefull you just replaced it with a new one lol i wanted a alternative :D

Thank you very much!

if you had put a little blue tack in socket and used the short bar it would not been hard to put it in. Other than that good videos.

The things you calling a Plunger or are coil packs they provide the high voltage to spark plug

How did you get the socket out after you dropped it ,tricky ??