วีดีโอ

It's pretty obvious reinkes are light built. I already knew that before I watched the video

several hundred degrees.....get your hand off it bro you're not fooling anyone with that crap

Very biased comparison as expected from a salesman. Plenty of incorrect information and not comparing apples with apples. Do your own homework and talk to all brands directly to find out real advantages of all brands.

Funny thing I’ve seen complete Valley systems blown over. The ball doesn’t always come out.

تحياتي لك من العراق هل من الممكن أن ترسل لي مخطط المرشه

Good sir , I will kindly disagree, we have them all 3 valley, Reinke , zimmatic from old to new and the valley would be our last choice , Reinke first , have not had any such issues at all that you mentioned in the video.

Reinke > valley.

Que loco, encontre lo que estaba bucando ❤ thanks

That’s my teachers dad

Thanks for sharing the value Tips and info

Hi sir good evening I'm also pivots operator can you give me contact number please 🙏

Witch country dear sir

Witch place sir that's country

Great explanation from fans of this irrigation system.

The explanation is great and good and I am a fan of this system.

I got one I need help with. System fault on valley icon Outside for/rev operating sector detected.

Very cool! Now you left no advantages to hydraulic machines that used to tell that only hydraulic machines are straight while moving and continuesly moves without stopping

Thanks, saved me a service call and helped me figure out which motor went out. Wasn't quite sure how to check until this video.

Hello sir

i need training it is possible or not

Thanks for your lessons, But i have a problem, our pivot when is setting on100% runs after 20min the fiveth tower become misaligned, but if it is setting below 80% it runs good. I tried to change over watering timer, micro switch but no result, can you guide me inorder when i set it in100% runs normal?

I really need to know how to do a good alignment and if the pivot becomes out of alignment

Very good

Great video! Very Smart Guy … Great Guy to imitate!

Great video! Definitely going to pick up one or two of those volt meters!

Mu hubs is pretty darn impressive, knows his stuff. My dad would have loved these videos.

Nice work

You missed a very critical step by drilling out the 2 or 4 tiny holes on the sides of the top cap

Interesting though I'm in zambia Africa need to learn more, and ordering spares as well, need to learn more about the machine

Hello sir, I am interested in this field. I would like to ask you about it, please

Do you prefer the FWD/REV microswitch to click so close to the valley of the cam? I’m in manufacturing, specifically- Aftermarket pivot controls. My team and I build valley/Lindsay style Tower Boxes. I’m asking an honest question, not trying to say your doing anything wrong bc watching your video it makes sense to me and I literally build them!! Do you ever install a new tb and have to adjust the microswitches? I noticed there wasn’t any thread lock on the microswitch mounting bolts and none on the microswitch adjustment screw. Just curious about your thoughts. I need to visit a farm and start playing with these controls. Helps to better understand what techs are doing in the field. Maybe I can do a better job building them!!

5:30 eww what’s that green liquid

How do these do vs the Komet Precision Twisters? I think those are supposed to be like the Nelson Rotators?

they say that the sennigner iWobs and Wobblers are supposed to be like natural rain. That may be why they do better than the Nelson 3000 rotators. I've ran a wobbler and iwob in my parents garden off a hose inverted and let me tell you it did a very good job at it . the nelson rotator got farther out but i dont think it was as efficient. It might have been the plate i was using too. They have different plates for different applications. I like how both can run off a garden hose pretty much if its just like 1 or 2 of them. I've seen the iwobs used in nurseries before and they do a good job.

There is a pivot near my house, a valley. Has a komet twin 101 at the end and a booster pump. one year i saw it running and the stream had good distance then it looked weak. it would cycle thru that constantly. I'm sure it wasnt' a jet breaker add on. I think the pivots booster pump was malfunctioning. This year i haven't seen it do that though. Mustve gotten repaired.

The thumbnail shows a SR100 and a RB 70 as dual end guns. There's a few pivots around that either have the 70CW's or Nelson 44 or Rainbird L36's down the pipe and some even have those old FR guns at the end. You dont see that very often anymore. I know of a few pivots that have 70CWs down the pipe and then a PC100 and P200 at the end. I have not seen those run the P200 gun yet i dont seem to catch them at the right time. I'm assuming there meant for like a "poor mans" corner system, the system runs the normal sprinklers and the smaller 100 gun for a time then when it reaches the certain area in the field it shuts those all off and opens the valve on the P200 gun and that gets an area of the field that the smaller gun can't reach then when it times out it closes that and then starts up the impacts and smaller gun and continues on. I would love to catch some of those pivots changing modes. Those P200 guns are so neat to watch they have such awesome distance and coverage and the reverse cycle they whip back so quick. I know there not made anymore the FR guns always needed constant maitenance to be kept in service. Nowadays its more efficent and cost effective to use a SR nelson or a Komet Twin.. Putting down twice the amount of water going 1 speed both directions, not to mention those FR guns can give the overhang quite a workout if not set properly, brake and whatnot. One day i'd like to learn about how to operate a pivot, and even set up a traveler. I work on computers but this is a hobby.

I've seen these around where i live but it's rare. Usually they use those nelson rotators (r3000s) or those sprays (I forget the model or make). Valley where I live is very common, but if you go south you start seeing more Zimmatic than anything. Reinke, Valley, Zimmatic and sometimes T-L. I like the Iwobs i ran one off a garden hose once in my parents garden and it did very well just off a city water supply.

For the Valley ClassicPlus Control Panel model, to power the oscillator, the wire to be moved to pin 3 will be the red wire from pin 8. As already mentioned, the wind in the microphone is a bit troublesome. Good job, thanks for your help.

Thanks🤠

Very useful video, thanks for sharing

TUBOS ADUTORAS ACO HELICOIDAL C ABRACADEIRA FLANGES P IRRIGAÇÃO PIVO SANEAMENTO MINERAÇÃO TRANSPOSIÇÃO AGUA DO RIO SAO FC contato na foto a esquerda....

Control pivot _ thank yuo

And do you guys have any used pivots for sale

What would cause a mechanical stopping slot on top to stop working

Love how we cant see what your doing at the most important part

Great and informative video. But that potato of a microphone you used for recording purposes and then the wind didn't help. otherwise, thanks!!

Very cool

Nice

I need one of those trucks for up nort'

Super duper Mike ..