วีดีโอ

Thanks, that was great info ❤

This is one of the best explanation 💯

Fantastic Video!! Thanks for helpin g me to correct my technique. Maybe down the road you can offer some advice on how to appropriately select those numbers on my DEWALT such as you have. Thanks again......😊😊😊

Excellent video

I use a self tapr to start the hole then i use a drill bit and i saved so many bits

Thank you

I am 76 and never knew the proper way to drill. Now I do. Thanks.

drilling a steel is much easier than GI and stainless is the hardest to work on , also I don't have step drill , and I can't push through with my step bit

Great video

I ruined my drill bit yesterday coz I didn't have a clue on how to drill through metal plate 🤦🏾‍♂️thank you for this tutorial I'm going to try it this way tomorrow.

Thank you internet dad 🥲

Kebanyakan omong 😢

Use a centre punch

Same thing applies in machining. Our bits get destroyed because the feed rate is too slow, the spindle speed is too fast, and the coolant ratio is too low.

Thank you - great video. Straight to the point and super helpful.

Excellent video thank you brother

Would this be the same with self drilling screws? Or should i drill a pilot hole first

Wow. Saved me a bunch of bits and frustration. Thnks dude. 🎉

I’m 31 and I considered myself an expert at using a drill(supposedly a simple tool) except in the areas of drilling through thick metal. I’m always doing work to my enclosed trailer and I could NEVER figure out why it was so hard to drill through the metal. Thank you so much!

Excellent video. Thank you. Simply and clearly explained and you demystified metal drilling and helped me overcome something I've always found intimidating. You're a professional.

Great video! I burned through most of my smaller sized bits a couple of weekends ago drilling out some rusted and broken studs on my exhaust system. Seems I would have saved my bits and got the work done sooner if I had been drilling correctly.

Thank you for this video, as for your last words, I am my supervisor, so thank you😂

I just ruined some drill bits and stepper bits doing it wrong., by using hi speed and not pressing hard enough. I needed this video. Thanks for the lessons!

very well done! thank you!

Thank u for your valuable knowledge 🙂👍🏽

Great video. First time drilling metal and learned everything I needed in this video to get my project started.

well done, learned a lot, thanks

8 years later, thank you so much sir!

#1 do not buy cheap Drill Bits #2 use cutting wax instead of oil #3 use a steady hand

Thanks a lot man I learned a lot !

This is excellent. Thank God for TH-cam

You are... A real hero! Thank you so much!!!! Never though something so easy could get so hard if I was doing it wrong....

It's asolutely an ultimate guide for me. It solves my problems of drilling holes on hard metals which keep damaging drill bits even they are good ones. It's the speed. Thanks for sharing valuable tips

Your video was a SAVER. Now I easily fixed my metal desk frame (plus, I added a drawer).

I wanted to drill 3 holes in each of front two doors of my cars to install car speakers, took me an hour for 6 holes. Did with high speed. Didn't know it could be done this way, thanks Master.

Nice video ! What size punch tool are you using ?

Got some piece of hard steel today that I had to drill holes in. It was dusty, no curls and I had the hardest time getting it done, plus the bit was hot. I saw your video and I know now what my mistakes were, so thank you for the lesson!

Thanks for showing the proper way to drill metal. Very enlightening!

Helpful

You covered a lot of issues here. Great demonstration. I appreciate it!!!

I love me some big chips. Other day I watched a millwright running full speed on mild steel, making smoke, with an assistant just a-dousing the hole in lube. No clue.

Thank you!

HEY ! LISTEN YOU ¡! YOU DON'T BUY ! ME !! ANY NEW !! DRILL BITS !! WHEN ! THEY ! BREAK ! / BUST !! YOUR VIDEO !! IS ABSOLUTE ! UTTER !! CRAP !!! THIMBS !!! DOWN !!!!!!

I would never guessed to try SLOW and it worked👍👍

I've never used a drill in my life but need to drill 3 holes into aluminum. This was so freaking helpful thanks!

Thank you so much.... You deserve a big like & subscripe

Good video.

Thank you so much👏👏 Sir !! You really saved my day... Very 🙌 Informative video, explained it beautifully😍.

Great video.

Thank you so much for this tutorial. After smoking three or four drillbits I decided to look up the proper way to drill in metal and your knowledge and techniques are spot on. Thank you so much!