วีดีโอ

Live and learn. We call these "teaching moments" 😂

What Power can transmit this device?

“So good it ate thru it’s container”😂😂😂 I got shit like that too

Hälsa Diddan!

If you made the lever little longer it would distribute the power needed better. More precise so you never put to much force. Nice job though

mycke jobb men varför inte

Before I engine swapped my turbo brick, I replaced most of the bullet connectors for modern pigtails. The harness wasn't too bad, but all the connectors were falling apart. Thing of the past now, most of it has been deleted.

Kan man spola rent uppe i blocket med t.ex avfettning sen spola med vatten? Eller hur rengör man där uppe? :)

Truly inspirational

You don't need to pump the break pedal and hold to bleed. Simply crack the bleed nut till an uninurupted stream of break fluid comes, then tighten the bleed nut. Pour clean break fluid back into the master cylinder. Repeat for each wheel cylinder or caliper. This method works for either system. You'll save a lot of time.Cheers

peculiar solution

You just casually have a horror movie saw thing laying around?

I love your energy so much man, these videos almost always make me laugh

This makes me mad😭

hej

The masculine urge to just paint something

I don't think that's a very safe spot for that to be

I'm studying electrical engineering but I don't at all feel like an engineer because I could've never come up with something like this

Short story long😂😂

Where'd you get that from

I see two pistons here, one baby piston and an ant piston. and yes, the only pistons I have had anything to do with is on a boat engine XD

Definitely one way to check if it's tempered

Best of luck

Calmest unboxing ever lol

W

The tags in the title aren't even tags, it's just another complaint about that thing

"im not gonna regret this trailer" followed by "come on now i got 4 broken trailers" is very funny but also incredibly unfortunate

"Tree trailers" 😂 ska inte vara elak, du pratar engelska bättre än mig

So funny man

bro you are crazy😂😂

That's not made to break high torque...... User error. Do you use a ball pein hammer to frame, too?

Brushless have an idiot feature that cuts out. Brushed didnt come with that feature

Using it right and without the knock off battery would probably help

There is a tool for every job and this one has been used on too many of those jobs where it didn’t belong.

Untighten like a normal ratchet then hit the button to loosen. Youre burning out the motor on a tool that has little torque

That happened to my electric drill mixing mortar. Rip drill.... good run for 20 years! End of thought 🤔

kan vara ett felaktigt batteri så va försiktig 😃👍

😂

I can feel the pain in the "eugh", hope it won't be too bad to fix

Looks tasty. Could I give you a couple tips? Is the meat chicken? If so, cooking the chicken first and adding the vegitable is going to cook trhe chicken for too long and make it dry. Cooking the chicken first on its own like you did is good, as it will fry, where as if you add it after the veggies it will boil, but my advice would be to fry the chicken, then take it out, cook the vegies, then add back the chicken when the veggies are cooked. Other tip is to not add the noodles into the cooked dish unless you plan to eat the whole thing straight away. It looked like a huge amount of food, so Im guessing that you were gonna eat half, then half later? The noodles wiull get soggy, so keep them seperate, and add them when you serve. Use garlic and ginger, it would go so well with those ingredients. Get a few spices and just play around, every meal you cook, add some and see how you like it. id recomend cumin, coriander powder, tumeric, paprika, tandori masala, and pepper.

Looks good! I agree cooking is very enjoyable. Good video!

Enjoy, looks good, next time just cut the carrots very thin and rectangular, its called julienne cut😊

That parking brake made me almost die laughing

Usually people tend to enjoy food, in all seriousness though, that dish looks delicious

Is this the shiniest thing in the shop now?

That looks so scuffed I love it

That's actually really cool

Is this the same lathe that was bent when you were polishing it?

Don’t quit your day job

Not enough and too much is a very common issue with settings