วีดีโอ

hey can i get the file for this simulation please

it is use for vaiable both voltage and frequency?

Can you explain its working bro it would be helpful

Please for help, how to use matrix converter to converter from single phase to three phases in matlab simulink, thank you.

is this single phase step down mid point cycloconverter ?

do you have the document of multisim?

Can u give ur mail id or number. I want to make a project design from u

Can U explain this working principle of this block diagram. How we can find out THD

How much is the resistance of the resistor

in my opinion multisim has too many pins missing on the Ics, has a lot of passive components, but much to few ICs that are needed for many simulations.

Perfect video bro. Could you help me with a circuit? I can pay you a bit for your troubles

please delete music... it wants me to stick a soldering iron in my ear.

in my opinion of multisim is a poor product which has a high failure rate, a lot of passive components which is alright but the essential ics are omitted, almost all the ics are missing pins what national instruments should do is go back to the drawing board and came out with a product that is functionable.

Can someone tell me what is the job of R1 and R2? Why they are there?

A single phase fully controlled converter is supplying power to a separately excited DC motor drive of 1.75 kW, 200V, 10A, 1200 rpm. The armature resistance and armature inductance values are respectively 1.2 Ω and 1 mH. The supply to the converter (rms value) is 220 V at 50 Hz. Obtain the current and voltage waveforms in the source side and on the motor side (i) when the motor is working at a speed of 1000 rpm, while delivering rated torque. Calculate the firing angle of the converter theoretically for this operating condition and verify that the motor’s working through simulation. (ii) Change the firing angle abruptly to 60° and check what happens to the speed of the motor after the steady state is attained. Get the waveforms for both operating conditions. (iii) Further, if SCR device 1 (T1) gets short circuited, show how it affects the functioning of the converter.

kehna kya chahte hoo

🤔🤔🤔🤔

This is latch

How you generate that truth table in multisim ?

why you did't used the clock voltage from the sources ?

What the hell bro 😒🙄 I made the entire simulation like you and the output is same as yours ...... But the output is wrong only 1 segment is changing from 0 to 9 🙊

I dont know why I tried many jk flipflop multisim circuits and tried them but wht I do with interactive digital constant and probe doesn't work. It works when I use double throw switch, led and ground.....

best simulation

i dont understand how he took outputs from the back of the and

Very very helpful, thank you Sir!

Is this inverter can be used in wind energy conversion system

Very informative video. number of things i came to know about multisim after watching this video.

Is this used in wireless power transfer

ممكن شرح عن ذني المواضيع Oscillator: phase shift oscillator, ramp generator, Hartley oscillator, crystal oscillator

Where i can find a Time Scope ?

do you have an email?

Perfect video bro. Could you send me this file? Then I will be very good.

Please give me the logic If we want to reset this

Bro, can you mail this file to vineethindraganti@gmail.com Thank you!!

hi bro, you have done a great job. can you share the source file of this circuit

😒

Thank you!! this saved me in my class

Hi, is it possible to use DIGITAL_CLOCK component insted of U7 , if yes what i have to change ?

what about 6 to 64 ?? please help

What is the reason behind setting pulse period 0.01s instead of 0.02s? As input source frequency is 50Hz.

Can you send the multisim file google doc link please

What components requied

great work!!!! Can you send the simulation file plz

how to get the phase shift as well as Vin, Vout and the gain

Bro could you please send me the proteus file?

Awesome, thanks <3

Sir can you please send me this file, i tried but couldn't get the result, this is my email id: abivenkatesh16@gmail.com, thanks in advance

I did this exactly same circuit/procedure on MultiSim 14.0 and it did not oscillate. Also, pretty much every other oscillator circuit seems to not oscillate on MultiSim 14.0, any ideas?

Key r and s represent for what?

Can i know, what is the value of resistor for 2kHz frequency?