Aiko Man
Aiko Man
  • 3
  • 27 244
Trouble shooting Roland SP-540V
Trouble shooting Roland SP-540V
มุมมอง: 27 215

วีดีโอ

ความคิดเห็น

  • @Paios
    @Paios 24 วันที่ผ่านมา

    Damn that carriage rail filthy

  • @KushCanvas
    @KushCanvas 2 หลายเดือนก่อน

    I have the same issue going on. Changed ribbon cable 2 times, changed cut carrige sensor, change cut carrige board still says invalid id right pos. Any help with this would be greatly appreciated.

  • @uneedasign63
    @uneedasign63 5 หลายเดือนก่อน

    Ribbon cable everytime

  • @ronaldmartins9839
    @ronaldmartins9839 ปีที่แล้ว

    Change the flat cable of the clipping cart, but first clean the sensor behind the cart.

  • @tamraloomis4592
    @tamraloomis4592 ปีที่แล้ว

    Can you tell me how to find the ip address in this machine

  • @geoffreymockett
    @geoffreymockett ปีที่แล้ว

    I Had this very same problem, then i did this: th-cam.com/video/NxHb7WIYWcU/w-d-xo.html and it fixed it.

  • @gurvindersingh-sn9vk
    @gurvindersingh-sn9vk 3 ปีที่แล้ว

    How to clean drain bottle

  • @abcprintingcompany3850
    @abcprintingcompany3850 4 ปีที่แล้ว

    The problem is in the flat cable cut car,I had the same problem and so I solved it by changing the cable cut car,Good luck.

  • @ronaldmartins9839
    @ronaldmartins9839 4 ปีที่แล้ว

    Solution: th-cam.com/video/CgrcdcaJseE/w-d-xo.html

  • @reidoadesivo5427
    @reidoadesivo5427 4 ปีที่แล้ว

    Cable flat carriage. Change him

  • @timkaz227
    @timkaz227 4 ปีที่แล้ว

    Had this issue a couple month ago. it was the ribbon cable. There was no visible signs of wear, the wires inside just wear over time.

  • @johngolojuch6764
    @johngolojuch6764 4 ปีที่แล้ว

    When mine did this, I just installed a new ribbon cable, not the encoder.

  • @Hossam_world
    @Hossam_world 5 ปีที่แล้ว

    I have same problem, What can I do?

  • @DaudsWorld
    @DaudsWorld 6 ปีที่แล้ว

    I wonder if he fixed it.

  • @mariotece1
    @mariotece1 6 ปีที่แล้ว

    Clean the encoder with alcohol.

  • @reidoadesivo5427
    @reidoadesivo5427 6 ปีที่แล้ว

    The problem is in the flat cable cut car. I changed cable and finished the problem.

    • @mysterenigma9361
      @mysterenigma9361 6 ปีที่แล้ว

      My Roland SP540V only came with 2 pinch rollers (Ones with wheels) So altogether it has 2 with wheels and 2 metal ones. Is this right? Thank you

    • @rainyjr68
      @rainyjr68 5 ปีที่แล้ว

      hello do you know if there is a video on what the exact part is and/or how to change it? Thanks

    • @novacriativo
      @novacriativo 5 ปีที่แล้ว

      Você poderia me dar mais informações sobre essa manutenção?

  • @xtremegraphics3011
    @xtremegraphics3011 7 ปีที่แล้ว

    el problema es el cable blanco flexible que va de las tablillas a la navaja de corte

  • @rmwjohnson
    @rmwjohnson 7 ปีที่แล้ว

    The problem is that he had the 'left' edge pinch roller in the center. Notice how it paused in the middle as it went over it but it never paused on the very far left side? Invalid left pinch roller was the message he got. He simply had the wrong pinch roller in the left position. Swap the pinch roller on the very left edge with the one to the right of it and his problem would have gone away. You can verify this is true by how the tool carriage paused over the very far right pinch roller.

  • @roodmnt
    @roodmnt 7 ปีที่แล้ว

    Went through the same procedures, but the best we can get is 0mm media width reading....

  • @ProGamerToka
    @ProGamerToka 7 ปีที่แล้ว

    If you want help tell me on my email i will help you lifeandnew@gmail.com

  • @crgrove
    @crgrove 7 ปีที่แล้ว

    I suspect he posted this "public" so that he could show a techie... this was not for us, methinks.

  • @universodascopias4965
    @universodascopias4965 7 ปีที่แล้ว

    same problem... did find the solution ??

  • @neilcotter6903
    @neilcotter6903 7 ปีที่แล้ว

    did you ever find a solution?