วีดีโอ

The SF750 should be sufficient for your build, as the Ryzen 7 7800X3D and ProArt RTX 4080 combo are relatively power-efficient for high-performance hardware. However, if you want more headroom for potential upgrades than go for SF1000

Awesome! Thank you for the reply, and just to ensure there is plenty of room for the SF1000 as it’s the same size as the SF750 correct?

I think SF1000 is longer by 25mm

It's overkill for my setup as I'm not overclocking the CPU and due to compatibility issues with certain coolers. I could have gone cheaper and still gotten everything I need.

@MarinkoTambur ahh I see! I'm currently considering the Asus Prime 4070 Ti Super + Ryzen 7 7700X and the MSI B650i Edge for Mobo..

Standoff-5 + Standoff-30

Is yours 2.75 slot mode?

Yes, first I had it in 3 slot mode but had to move it to get more space for the cooler

OK so the 20 + 10 + 5 that it comes with then?

Uh kontraverzno pitanje 🙃 Ja licno mislim da se isplati i da se moze naci posla ali sve zavisi koliko si snalazljiv kao i sa svim ostalim poslovima. Ali ako je glavni razlog da ucis 3d zarada i pare, mozda nije najbolja industrija.

Hi, I posted the short with the moving droplet after the tutorial, so there's no explanation included. I drew a Bézier curve on the bottle to serve as a path, and within the same geometry node setup, I converted the curve to a single point and instanced a separate droplet to follow it. Using the Trim Curve node, I animated the droplet along the path. Additionally, I used the Geometry Proximity and Delete Geometry nodes to remove points near the curve, creating the effect of the moving droplet erasing the other ones.

th-cam.com/video/dt6wGTmOYTg/w-d-xo.html

@@MarinkoTambur WOW ! Thank you so much for fast reply !

its combination, but most of it was with ND's but also most were shot in 60fps

@ interesting. Looks good. Do you use a 120 shutter for 60fps? I’ve only recently realised that the 180 rule on higher frame rates still decreases motion blur.

@imeanbillya I try to keep shutter at 180 as much as possible and yes you are right, higher frame rate will result in less or no motion blur even with following the 180 rule.

@ I guess it made more sense with film shutter because you couldn’t have the frame rate and shutter speed the same. Genuinely might start making it as close to 1/48 regardless of frame rate.

Hvala Dario

In the video he says v2.5. So that is the NCase.

yes it is NCase V2.5

Tesko je reci ovako ali par stvari koje mozes pogledati je dal ti je frame rate isti na timline i u exportu i pod clip attributes. Isto tako moze biti ako su snimci sa telefona (GoPro) i na telefonu je ukljucen auto fps. Ako nista od ovog nije slucaj posalji mi mail pa cemo u detalje.

@@MarinkoTambur Imam snimke sa kamere,gopro-a i telefona.Time line 25fps.Kamera i go pro idu na 25fps-a ,a telefon snimci na 60fps-a zbog usporavanja snimaka.Mozda je tu problem....Ipak se vracam staroj ljubavi Premier...Hvala na pomoci ...

kako god mislis da je najbolje. U slucaju da ostanes u resolvu jedno od resenja ti je da transkodujes snimke sa telefona i gopro, mozes korititi Shutter Encoder ili handbrake i prebaci ih u ProRes ili DNx-hd ili cak u H265. Mada ako je variable frame rate iskljucen nebi trebalo biti problema

Hvala Dusko

🤣

Pozdrav. Sve zavisi koliko vremena posvetis tome. Osnovne stvari se mogu nauciti za par dana. Najbolje da pocnes od Blackmagic official treninga www.blackmagicdesign.com/products/davinciresolve/training i naravno mojih tutorijala 😁

What made you think that?

pogledaj ovaj video th-cam.com/video/dLLE3JacTYE/w-d-xo.html

Ma to po malo kad radim tutorijale na kraju sta ostane, nista posebno. Hvala u svakom slucaju :)

Hvala, bit ce jos :)

Razlog zasto blender, jer je besplatan i dostupan svima i kada se nauce osnove i principi lako je preci sa jednog programa na drugi ako je potrebno. Vjeruj mi potrebno je dosta vremena da se napravi tutorijal tako da nevjerujem da ce da bude nesto za Maya, ako ista drugo bude mozda bude Plasticity.

Pozdrav, to nije moguce. Mozes da modelujes nesto na osnovu slike ili da koristis Ai da generises model ali da konvertujes iz jpg. u obj. to ne! Mislim format kao format ti mozes prebaciti u obj ali slika ce i dalje biti dvodimenzionalna.

@MarinkoTambur hvala puno

hey it's kind of combination of techniques from @bradleyanimation120, @seanterelle, @CartesianCaramel tutorials and it also heavily relies on @bradleyanimation120 free presets

Hi, it was based on this tutorial th-cam.com/video/lHSNui8lgyI/w-d-xo.html

Thanks! There might be a tutorial.

Hi if you are asking for PCIe I think its 19cm if im not mistaking. there is a link in the description. Rest was stock cables

Hi, yes it should fit. I've seen some photos on reddit that it fits.

amzn.to/483Pxez

Hi, I don’t game a lot, but for example, in Black Myth: Wukong during gameplay, it’s in the mid-60s, and I'm getting just over 90 fps. During heavy rendering in Blender, it’s also in the high 60s, but when I'm doing some heavy simulation or running Cinebench, that’s when it shoots up to the mid-90s.

@@MarinkoTambur what about idle? thanks!

Idle is 40

@@MarinkoTambur you should probably get a noctua fan swap for your cooler then.. just a suggestion!

I tried lowering the voltage more but I'm getting better performance rendering with these settings.

The CPU is very power-hungry, and with this setup, it's impossible to cool it effectively, so I'm not getting the full potential from it. The motherboard also has compatibility issues with the cooler I purchased, and it's probably overkill for this build. I could have saved money by choosing a cheaper option that would meet all my needs. A better choice might have been an AMD chip, as it would be easier to cool

Thanks, yea I know now. My mistake for not doing better research before buying the parts but for now it's getting the job done.

@@MarinkoTambur Glad to hear that it gives you everything you need!

Thanks, I might do some of them soon.

AXP90-X53 Full Cooper

NCASE was the only one available at the time when I was buying it. So far no scratches 😀

Thanks. When I was buying this one was available and 2.1 was restocking

Which L12S do you have? this one is low profile version, and it only fits in High-Clearance mode on Z790i

hey check out @CartesianCaramel I made this following his videos.

Im sure someone else would be better to answer this as I'm no expert but from what I understand if you are not planning to upgrade to 5090 anytime soon and you don't have any power instability with current set up I don't see the need to upgrade.