วีดีโอ

Sorry, no plans, just use the diagram from the board. It wasn't that difficult. Have fun.

The rc/drive system is independent of the mower system with the exception of the shut off/brake.

Check the tube at the bottom behind the roller.

Electric wheel chairs will weight anywhere from 150-250lbs, and have a rider weight rating of 300+lbs depending on the model. I think a tow behind is very doable. My current build is for just a 21" push mower, but I'd like to upgrade it to a full riding mower deck 40"+, but I will have to figure out how to power the deck and 24V alternator. Right now the Alternator runs off the self propel pully and belt, so in theory it will charge itself up, and never need to be plugged in. Others have done it, so I am sure it will work.

checkout motionsic RC for gimbles

Try to find an Hoveround HPV5 36V motors. They might be able your weight requirements. They are built like tanks and can move quite a bit of weight. Good luck.

Check the tubes from the bottom up. They all come apart fairly easily with clips. When the motor goes out it usually makes a high pitched squeel or a gear tooth is broken. Ours lasted about 10 years with constant use and two big dogs.

It kills the spark plug only. It doesn't do anything to stop the blade from spinning. I didn't want to compromise the safety of the spring which applies pressure to the break.

I was fixing that for a friend. You will have to find the model number on you vacuum and look it up on Google.

You can take the entire suction path apart. Get a wire coat hanger that your not using for clothes, it makes a great tool for this if needed for the long pipe section. A new filter set couldn't hurt, or wash the sponge filter.

@@chainrection774 thank you, I will do that. I ordered new filters. I pulled out a huge clog.

The motors i have are pride z. I don't have the full specs. I would definitely go with 10" wheels if you can. I bought second hand and didn't have a choice. The speed can be throttled back on the transmitter. I believe it is under exponential value?? It was mentioned in another reply in this video, I'm sure you can find plenty on the transmitter on here as well. I can't comment on the torque but I would figure it is linked to the max amperage of your batteries. I did add giant 13" wheels to it at one time with no torque issues but took them off due to fast battery drain. I don't like seeing my wheels slip in wet grass when I'm watching from a distance cause I know that is lost power.

I would look into LIDAR integration. I didn't want to go fully autonomous due to safety and extensive development. It should be possible though.

Yeah, just make sure ground is tied between the sabertooth and receiver. Mine didn't work until I did that. Just for the signal at least, but all ground should also go to the chassis.

Can you elaborate on the ground issue? I'm not following the problem. Thanks

It isn't bad at all, at least not any worse than on a drone zipping around. Just make sure it is a wide FOV and you pull separate 12v power if you're running a 24v system. I would recommend bigger box type goggles actually with a big FOV as well. Resolution seems less important.

@@chainrection774 thank you sir, I do alot of fpv and tried it on some of my nitro planes and that was a no go, looked like a blender in the video.

They are all nearly the same of that style. Is the brush no longer rotating?

@@chainrection774 thank you.. you know what it does spin but then it will suddenly start making this loud annoying buzzing noise like something got stuck in it. I’m not sure if it’s the belt or not but thought it wouldn’t hurt to change it but for some reason Shark doesn’t have it (I called) and I can’t seem to find a belt for my NV90 model. eBay & Amazon don’t show one for NV90 but there must be a belt that will fit. I figure I may need to take it to a vacuum shop or something?

Thats what the dogs are for, now an RC Seeder for sure.

What's the issue?

@@chainrection774 I bought the flysky controller with receiver. I can’t get the right settings in my radio. I want to split the wheels when turning to make tight turns plus I am mowing on steep hills. I have each wheel going different directions an forward seems ok but steering is not

@@ellismccoy2020 Try reversing a channel, 1 or 2 in the settings of the controller.

@@chainrection774 I have done that. It took off in circle an ran over me before I could jerk lead off

I will add links in the description later but it is a ev100 for the headset, Wolfwhoop Q1-Pro 0.01/25/200/500/800mW Switchable 5.8GHz 37CH FPV Transmitter, Caddx Ratel Newest FPV Camera 1/1.8'' Starlight HDR OSD 1200TVL 16:9 NTSC camera. I tried a 120 FOV camera before and the field was too narrow. So I went with an 160 or higher. Kind of a give or take on the fov, you need to see around and in front but it distorts the perspective a bit and takes getting used to. I don't get perfect lines in the yard but I don't care, I'm not pushing the dang thing anymore. I added some fatty tires that aren't in this video and I will make a new video sooner or later.

@@chainrection774 Thanks so much...Just moved and I have no shop at the moment but sometime this summer will be up and running. Should be able to start rebuilding mine then.

Just tried those settings, helped a lot. Thank you.

@@chainrection774 Glad it helped. Im right at the time to assemble all the parts for my mower minus a few things that I still need to pick up. I love building things to be lazy with.

I found them but not sure what number to set them to? what a good number for them ?

@@kentanch2601 sorry its been a while but if you havent figured it out... The FlySky radio used here, channel 3 and 4 are mixed together and you will want to lower the expo setting for each channel to say... 50 or 60 and save. then drive it a bit and then return and lower some more and compare the feel. You still have full input range doing this, just not full blast at first touch. You might like channel 4 which controls left and right movement to be even lower than ch. 3 which will be forward and back. That way you will maintain a straight line easier. There is also a setting per channel to dumb down the max input value of full blast. I dont cut the grass at 6 mph so I knocked down those limits to suit lawn mowing instead of drag racing.

Sto usando un Eachine ev100 per un auricolare e non registra.

@@chainrection774 capito lo avevo anch'io, ottimo lavoro, ne avevo costruito un anche io ma usando due esc e un mix segnale Ma adesso ne voglio fare un altro utilizzando un hoverboard e segnale PPM invece di prendere la sabertoooth

@@edysalto6304 Potrebbe essere fatto. Ci vorrebbe più lavoro per decodificare l'Hoverboard piuttosto che costruirlo da zero. Inoltre, avrai bisogno di nuove ruote. La coppia e la carica della batteria saranno sufficienti?

@@chainrection774 th-cam.com/video/5QavWOvY96E/w-d-xo.html

th-cam.com/video/d5Pv82Sy5zc/w-d-xo.html

Great work on yours. Like the wheels, you got the big motors.

@@chainrection774 actually just started another one. A bit bigger. Mower has a 20 hp briggs and stratton and it has a 44" dual blade deck. Used to be a pull behind mower. I've got 2 one horse motors to drive it. Can't wait to get it going

@@DTB2.0 share it when its complete. Can't wait to see it.

@@chainrection774 I definitely will. Thank you sir