วีดีโอ

Any one help me in this project

plz tell me with using CNC shield

App showing no data recieved. How to fix this ?

at PID section i can not uppload saying wrong value how to fix ? please

Hello, can you upload they circuit diagram and the code again please? The link isn't not working anymore

Is it good when i use proximity sensor than ir sensor?

Thank you very much.

Thank you very much. You solved a big problem I was facing

How much power do you need for the four motors?

Good ❤

One question, how did you make the bluetooth connection with the application work on the hc-05 model (I'm doing the same project, but the bluetooth connection is not working well)

App not Available in Play Store. ez gui ground station

I want an app which the sends Mobile notification as a command to hc-05 bluetooth module .please help me anyone

Code nai hai

Sir can I use 9v batteries instead of li-on batteries

i want code , can anyone send me ??

where is the code ??

Broo How did you do that without calibarating the ir sensor ??🤔

Boadrate 1200.N.8.1 Per chalegi

Great video!! the link for the code is not working though, can u please upload a new link.

I can't download code from link. Please someone give the code🙏🏻. I'm really need the code

i want arduino code

Guys these tips were suck donot try follow these steps only stop the warning but aux is at the same time nớt conducting any information

Code ???

Bro in AUX it is showing not enough information please help

Hi bro I had problem that ez gui app is not available for new version of phone on play store

Can i use dc motor except steeper motor

when I place the robot vertically steeper motors are continuously rotating and stops when i rotate it by +90 degree or -90 degree I also done the calibration and Aux and pid settings. Please help me to figure out the problem.

Can i work with phone I haven't pc

Hi sir my group of science fair, is making this experiment and we only have some day, the code don't work and we need some help of us. Can you pls help us with a new code. Plsssss😅

The model is not moving after uploading code also

Thanks bro

Sir, Code doesn't open and received message as.. 'The file you have requested doesn't exist'. Requested to upload the code sir.

Hi there are many error in code please. Help bro plzz make new code of this plzz it is urgent

How did you make the track?

love it so much. Question: in Balancingwii notes that We must add resistor when the power supply has more than 12v. Can I use it without resistor when the power is under 12v, e.g. 11.1v (3 lipo batteries 18650 - 3.7v each)?

Great demonstration i understand very clearly how to config mine now thanks alot

Hi sir Are you selling the pcb? If so i am ready to buy.

For those whose bluetooth module HC05 is not blinking its own LED as shown in the video, connect EN to 3.3V and VCC to 5V, then you can carry out the AT commands. Also, remember to put question mark (?) after each AT commands such as (AT+UART?) instead of (AT+UART). Also, when putting new names and password, no need to use inverted commas , for example, you can simply use (AT+PSWD= 6754) instead of (AT+PSWD= "6754"), you can also cross check with the original password of Bluetooth module to compare the new password format with the exact format of original password for simplicity.

Bro home made pcb video

Sir please give me the pcb file to order

Sir give me the pcb file

Sir give me PCB file link I want to order it sir please

Sir can we use gaer moter ??

Sir can you make a video on how to make connections because for beginners it is not possible to understand the diagram

Can we use cnc shield and will be the code changes.just to avoid buying pcb .thanks in advance

No need to drop the voltage going to the rx pin?

sir send lin to programe arduino

Hi, great work! Could you please provide a link to purchase the wheels?

Its lipo or lion