วีดีโอ

Very helpful just the bottom nut that spacer welded to nut what point in it and what direction supposed to face?

What are symptoms of failure? Can these be tested?

Thanks for the info. I like your way better than taking everything apart. I was able to reach them and change them. Thanks again

Wicked💪🏻

Do you think it would hurt anything to put a little penetrating oil around the old sensor before taking it out? I've seen a couple people say they broke the sensor trying to get the original one out. Great video, thanks for making it.

How much did you pay for it?

Damn. I pulled out the old sensor, had oil/ grease all over it.. so I'm thinking the seal is leaking oil through.. ugh.. Any video that shows replacing that or need to take to a shop?

good video what causes rear tires to cup?

Thank you! doing mine soon once part arrives.

Nice . Thanks for showing that can be done without removing that piece on the back of the van

Thanks for showing how to do that. Now I can get a new one for my wife’s van and install it

lol like the fire it up fire it up.

Very good vid!! Yes- my turnsignal was flashing quite fast…now ill change my bulb tomorrow Because of your great video!!

My 08 escape 3.0 been doing this same crap for over a year. I havent changed mine yet but I will tomorrow. Hope it fixes mine to! If it does i owe you big time for this video. 👍

What Scan Tool did you use!?!?

Awesome, thanks for sharing. I’m about to install on my OBS F250

Hi bro where to find bulb socket because it's got burnt Mattel part and getting bulb replacement 3 times but still same issue continues so I couldn't able to find. And thing is some is available of older model of ecosport so please help me with this bro. 🙏

Where was the step to install the boot tie strap/clamp on the steering rack? Or did you forget to put it on?

Hey, I’m looking at converting my 350 Dooley Chevy, and had a question, the medium duty kit for a flatbed, puts it as mounting on top of the frame rails. But the hoist cannot nest underneath the frame rail and has to set flush, which makes it 11 inches of lost space before the flatbed Elevation. Is that why you nested it underneath the crossmember and reinforced it? Just trying to get some ideas before I take the bed off and custom build my flatbed. I actually already converted a 2500 with the light duty and it just with bolts on the tube crossmember About hoist nests underneath. To me it’s all about space and being able to keep my center of gravity down.

Thanks for showing how to do that.I could not get it

How can i get them out of they are stuck?

ThoseAmish ate really good and fast building.ive seen a fee of there pole barn builders they have built,how long did it take them to do that one? Thanks for sharing

Thank you very much for this . I was watching guys telling me to pull thewhole inner fender off

Wow, great job

So what caused it

Fast way to change a fuel pump 😭

If I was to approach this from the engine bay, would I need to remove the cowl cover along with the air box? I tried to remove components of the exhaust system, but they are extremely hard to remove. Thanks.

Sorry everyone meant to say 2010 thru 2020 on Toyota Sienna mini vans

What dash lights came on that made you change wheel sensors?

Where Toni get that. Changed my oil the first time yesterday and got oil all over the place. Freaking stupid how they put that filter in there. Thanks for video I wish I would have watched this first and got that part

I have a question. How much should a front wheel speed sensor cost to buy? I have seen both front sides for $30 up to $150 for one side and then Toyota wants $370 for one side, that’s the price for the part in a plastic bag, they charge $165 per hour for labor.

I used my GB40 to start 2.5L Camry. Battery was not completely dead just too weak to start the 🚗.

Yes I screwed up at one point and said fuel filter lol. I was tired and hot and out of breath doing stuff lol. My bad

Great video ! I want to point out that when taking old sensor out sometimes the plastic part that goes into hole gets stuck and part of it comes out . Then you need to remove that plastic out with a screw extractor in order to put new sensor in .

Thanks for saying about the front one being a 5 mm Allen bolt I never would have figured that out right away ,it's so Rusty. I don't know for sure yet which ABS sensor is bad but looking at them the front right one has a crack in the base of the center where the Allen bolt goes through so I would assume that would be a good place to start.

thanks

Believe thats my problem on my 2500 ram. Thanks

ماسكين الدوله النصارى ذولالاتتمشكلون معاهم تفاهمومع اوختكم هند ربوبنتكم ياعيال الزنى يومين

Are both out tie rods going to be the same amount of spins? I forgot to count on the first side

These vans are actually known to have a weak rear end. So towing or not, the fix is those heavier shocks. Monroe 58624 handling immediately noticeably improved.

I was trying to get that end on and could not get it up enough to get it on. Thanks for explaining how to do it.afyer wasting two hours busting my ass your way took me 5 minutes lol

Nice. Thank you this saved me a ton of time. I was trying a 5 ft pry bar trying to lift it up and it was not working. Feel like a idiot after doing what you said lol. Super easy

Straight to the point, nice!

I was tweaking trying to find the right bulb for this. Thank you for not just telling but SHOWING us in this video as well. Much appreciated 👍🏼

My truck is making that noise. At least know I know what that is. Thank you I’ll take it to the shop I’m not mechanically inclined lol

Thank you . Help me get it changed

Thank you . Help me get it changed

Sister got oil change at walmart and it was like that. I didnt think i was ever going to get it off lol

Thank you, saved me alot of time trying to figure that out

Thats looks like a nightmare