วีดีโอ

ULTIMATE PLUS PAINT PROTECTION FILM 😮😮 Signature Features -------------- Heat Activated Self-Healing Topcoat Constructed from an elastomeric polyurethane, ULTIMATE PLUS will self-heal light scratches & swirl marks with a light heat application to the film's surface. Non-Yellowing Our proprietary film formulation will not yellow from UV exposure, ensuring protected areas are nearly invisible. Discoloration & Stain Resistant Don't worry about specs, spots, or splotches from contaminants. ULTIMATE PLUS is stain resistant & will maintain clarity under the harshest conditions. Prevents Wear & Tear Stop rock chips, nicks & scratches in the paint, and keep your vehicle looking as good as the day it rolled off the lot. Edge Seal Technology Lifting & delamination are a thing of the past. Our signature Edge Seal Technology ensures film stays stuck & keeps surfaces protected from contaminants www.xpel.com/products/paint-protection-film/ultimate-plus

dude, i have never seen such an informative video like this one. very entertaining and also tons of knowledge. great video bro 💪🏾

Such a BEAUTIFUL car !

Can’t I just take the fender and the light bucket together?

Can’t I just reset the ecu w my scanner?

Installing front and rear for a customer, NO instructions, missing parts, shit service! Poor engineering, powder coating as well. I wouldn't recommend their products to anyone.

Found your channel and demand more content! Hope the Z is coming along 👍

Great video bruh 👍

Is it loud inside the cabin on the highways?

Why is the flywheel insanely thick? I understand it has to make up for the adapter but it’s what 2-3x thicker then needed to just make up for adapter.

What transmission is that

any updates? after a year

love this car from the moment I saw it in NFSU2

You could easily take off the upper and lower plenum and have really easy access. Saves me time

Seam sealer the panel seams not the welds

My 06 6MT just cracked 100k miles. I've replaced 3/4 wheel bearings, 2 brake calipers, gauge cluster and fuel senders, window motor, all coil packs but it's never left me stranded. It does need a more work than my civic, but overall its been reliable for a sport coupe. I upgraded the exhaust to a bassani dual cat back and it sounds amazing. Love this car. I keep thinking of replacing it with a newer car but nothing under $70k excites me. RWD, manual, 4 seats, 300hp, under $20k is hard to find these days

Am driving M45 do I have to do them steps or can I use obd2 scanner to erase the codes! Also the car shut off after a few minutes… @windowsdown

Subscribed and in agreement with so many of the other comments on attention to detail. You communicate important points without any distractions or "fluff". Well done! Thank you!

Thx for yo honest thoughts experiences on Apex kit, i have a 240Z which will under restore mode next year,,which i would had gone with their kit but not any more, yes parts were never cheap for these cars n the last things u fine out after yo order that it will take forever n then when u finally get it its damage n doesn't works as it supports to or now u have to modify to make it work,, i don't buy that,, T3 for me now, thx for save others from same mistakes

I love the old school orange display. I miss my old 350z.

Can you just disconnect battery

You happen to know if the window is same as 350z?

Good stuff thank you.

This I think is the best reveiw of the G35 hands down🔥🔥🔥

How much weight do you think you are saving with this swap? If I recall the L6 is a bit over 400lbs. I figure the CD009 is probably a bit heavier then the Datsun 5spd. I wouls guess a savings of 100-150lbs

Update on 2024?

Nice job on outlining the process and steps. I just completed this exact same thing on my car and used practically the same steps. It took a lot of effort with the wire wheel (days!) and I swept up endless piles of debris like you did. This is the third time I’ve done this so I finally realized that a cheap paint suit from Home Depot was a Godsend. The raptor liner sticks to skin for a long time and ruins clothes. The suit was cheap protection. The results are worth it though. The finished product looks fantastic. Great video. 👍

Besides the tires it still looks stock. Never thought to do aesthetic mods ?

i’m trying to think of how hard or easy it’d be to get a 300zx speedometer inside the 280z rn

Do you have to remove the engine to take out the chassis harness

You think 370z diff will work for L series ?

I would have just bought a 280z fuel tank from S30 world. That's too much bastardizing of a perfectly good car for no reason.

So on the revup there's 1 angled and 1 regular on the back of both right? I've changed the cam sensors but was kinda confused om the exhaust valve timing control sensor..that's right next to them right? Thanks a bunch.. so basically 2 of each

I got P0345 wtf do I need

What do I do with the extra light bulb that was on the side marker

hi, i have to buy this vehicle on this week, 2006 model, is it ok for buying?

as of today, how's the headlight doing?

One question,is a front wheel bearing the same as a rear wheel Bearing? For the g35

This is best video. Love the charts. Simple + easy to understand. Thanks

damn..i wish i had watched this before i bought my AE kit... fml At least other people will :)

Just bought a ‘06 G35 sedan, got it with 164k miles and mechanically, it is perfect. Obviously the fuel sensor is off and the tire pressure sensor also but all I had to do was change the HID lights since one went out and changed the front rotors and calipers. Drive’s amazing !

I just got the p1078 code today. It idles at 1,100 rpm. Its odd that the exhaust sensor on bank 1 is the same sensor as the intake sensor on bank 2 and vice versa

How has this held up over the year? I am doing a similar job myself now and prepping to a similar level. Planning to epoxy primer the entire underbody and wheel well areas prior to the raptor.

Toy Mill

Are you going to ruin this one by putting a Honda engine in there too?

If you want a car with a Honda engine, just get a Acura NSX.

Well done video. I own an 03 1 owner prior, knock on wood not experiecing any of the issues, given the doors do close by themselves. 139k. Edit: 11:48 😂😂👍 Love my G dude.

At 3:09 regarding the "infamous white box", lol, you have the right tool (a knife/razor blade), however, on the other side carefully slice off the 4 tangs that keep the plug from pulling out the back and then push it out from the front (plug) side. It'll take a bit of force to get it moving but it will come out cleanly as long as the 4 very thin tangs are cleanly shaved off. I believe it will be re-useable if you do this carefully, but may require a small screw if your plug fits loosely.

Why can't u do it step by step y'all jump to much and it doesn't help

Correct me if I’m wrong but it’s either epoxy primer or self etching primer. You can’t use both as they’re not chemically compatible