วีดีโอ

Where did you get the battery hold down bracket?

anybody know this? i bought this for emergencies. first generator. Is it supposed to run full speed all the time? maybe its normal but it doesnt seem to idle down. it has one speed under load or not. ive run the idle screw all the way in and that does cause it to really take off. so maybe loud is the idle. im not sure. tell me. I imagined it would just get fairly quiet without a load and it just isnt.

You shouldn't try this without knowledge of kubota's or the correct tools.

The brp front windshield electric lift works way better than I thought it would, great in winter and summer with it’s infinite opening adjustment

Just fyi those rubbers go between the roof and frame of the machine to stop the rattles…..😊

Made something similar to this for my 18 ram 1500 hemi 2wd, to disable everything in snow, with a switch on the dash. Wonder if this would work for the 2500 hemi 2wd I'm about to buy?

Smart move using the excavator!. I had my front and rear drive shaft shortened on my 67..... $900. Ouch

Great work

Make the driveway to the cemetery wider 🥰

Alex needs one taken down and put back up😂

Any fingers cut?

Should of got Diana Combs to help you while we were there😂😂

why the change

I got 1 its heavy as a cow.

Hello, Are you interested in testing our products? We would like to invite you to test the Flip Windshield for your 2021 Can-Am X3

There is another youtube channel "bareknucklebinder" and this guy lives and breathes old international trucks.

First, the slide has to be all the way in or out(depending on access. Back one cable end off each cable. The new motor has to clocked to the same position as the old motor. Install motor, reconnect and tension cables Operate slide to ensure limit switches(if any) operate properly. Often the failure is because the limit switches are set wrong. If the switches don't stop the motor when all the way in our out, it damages motor or gear box, and cables, and mounts

Good job Thanks for making the mistake and saving me some time when mine goes out.

Wow a 2018 and the gearbox went poop... my 2016 Keystone cougar had that cable system and I never had a problem with the motor or gearbox just 1 cable had broke. Dealership quoted me $400 to replace and I had to purchase the cable (because they couldn't get the part). I got the cable for $45, I replaced it myself and had it adjusted all in 25 min and ready to go again. You should always try and do the job yourself before dumping it off at a dealership and get ripped off. I'm sure this job would have been 100x easier if this didn't have to be done in such a tight space, nothing is ever that easy on these trailers. I also used a label maker and put a label below each slide switch so anyone who opens the control center knows what button does what slide.

This is why they get $150 an hour. You remove the center nut of just the top chain and remove. Slip out the gearbox from bottom chain and reassemble. Make sure to adjust slack per MFG.

One of the many reasons I sold my Open range.

know where to get the part numbers for the bearings and seals? I'm doing my 1993 International 3600 bus and can't find it anywhere

Wow, how’d you get so smart? I know you got it from Mommy💙❤️

Where’s your black tape?

Watch out…oh Fudge…lol

I like the modifications you made to the mill. I've been wanting a mill for the longest time. At one point I decided that the LT35 full hydraulic was what I wanted. The cost is a factor so I haven't gotten one yet. There is an LT28 for sale near me. I like that you changed the clamp and added the electric winch. Its allows you to stay on the left side of the mill!

Thank you for the video. Regarding axle stiffness, a solid smooth shaft will be stiffer and stronger (safer) than the all thread that was used. You'll almost never find threaded rod in bending like it is used here because all of the threads act like stress risers. This is arguably overkill, but if it was me, I would be using AISI 4130 (or similar) steel shaft, shaft collars, and bronze washers with those casters. Or retaining clips and bronze washers if you have a way to cut grooves in the shaft.

I need some paper towels, all I’ve got is rocks😂😂

Your Daddy use to be out in the open at minus degrees💙

This spot is going to be so much bigger and prettier. 😍

Lmbo

He’s a man of many talents. I couldn’t be prouder of all he’s already done in us like. I love you, Son🥰💙

I am truly enjoying your adventures... the music alone is worth coming back

So refreshing to see you cutting in the cut and not back dragging.

this works the same for the cummins option too hey?

Better stop stitching and weld her in 🔥 those tack welds are not strong jmo

The Blue Grass and closing with chill beats sold me... Instant subscribe

What is the top button on the door control panel for

unbolt that suspension. take the left side uhaul outside frame from the passenger side and put it on the driver side. driver side to the passenger side. you will have to drill 2 holes for the trac bar but everything else is the same. then the flanges will line up. this will not only look correct but add strength to your joint.

I think you should put the top piece as well Looks good by the way thanks for sharing

Im still trying to figure out why ram thought i needed a 120v outlet before a 7 prong in a 3500 truck. Thanks for the video.

I spent the day doing what you did. However I ran out of sunlight! I recently bought the 4700, as I got closer to my house it started going slower & slower. By the time I got to my house the 4700 was going about 15 mph! It took me several hours to go about 120 miles. It was the last 20 miles that it slowed down to a crawl. I replaced the fuel filter, & removed & cleaned the small screen housing. The screen was plugged solid. I don’t know how it even ran. Tomorrow is another day! I’m sure once the system is thoroughly bled it will start like a champ. So far I’ve had about as much fun as you’ve had. My armchair recliner brother in law wants to know why it takes so long to change a filter. LOL!

We love our Predator. I always us our battery tender. 👌👌🌵🏕️

More videos. Great work

Yea let’s get it. Need hats made😘

No memory from your Mom and all your smarts from your Dad💙💙

Steel toed boots weren't made to save your toes, they were meant for kicking stuff back where it belongs..lol. Proud of you Gary and i know your Daddy is to. I love you💙

That will be a good low maintenance driveway for many years. You could have made it look nice temporarily with a box blade. But you fixed it up for the long haul. Nice work.

Brings back memories i machined all parts of that front axle assy and assembled it in 1969 at fort wayne works

Not sure if I’m seeing this right, but doing the case drain like you did are you not sending unfiltered oil directly to the tank to be sucked up by the pump if you have a malfunction in the mower head?? It looks like the large rubber hoses you removed to take the top of the oil tank off sent the oil to the hydraulic filter before it enters the oil in the tank. I would be worried about sending dirty oil in.