วีดีโอ

why can't you use the nail flange again?

Where can you buy replacement panels?

Glad I found your video. The wind curled 4 stripes of my aluminum. Thought I'd replace it with vinyl. Nope! Luckily for me the neighbors had their aluminum, same type same color, replaced with vinyl. The siding crew was kind enough to save me 5 good full length pieces. Now I can tackle it knowing how. Thanks!

Information!!!!!!!!!!!!!!!!

Best teacher for teachings bascis of electricity.Thanks for uploading such useful video.🙏

This is great. Where are you guys located?

That is the coolest thing I have ever seen.

This time and age, if your house has aluminum siding, you're just a cheap azz to replace it.

thank you for helpful video. In this regard I have faced a issue. An split AC was installed wituoud using a vaccume pumpe instead it was done by refrigerator compressor. So the according to your video the moistuer probably will left inside the AC circulation. Is there any solution to remove it?

This is easily the most detailed instructional on aluminum siding I've seen.

and NEVER do this without work gloves !!!!!!

Thank you for this! I didn’t know what orifice bits were for. This cleared it right up. Very helpful 👍👍

Bill Anderson is the best!

"Ya can't go wrong! *SNORT*"

Where are these from? Where can we find the complete series? I found some on turbine-generator control but it didn't include the whole video. Really love this guy

Why are you taking this siding off and putting it back?

Oh my, you tore up the vapor barrier and did nothing to reseal it.

I found older aluminum siding at Ambridge Supply in SW PA. I replaced 6 panels with that " cool tool " and did exactly ( what a accent ) the dude did. Impressive.

Whoa whoa whoa you took out a couple pieces show me the top piece that is punched and locked into sill trim or utility trim to secure it??

Show me how to remove the last piece smart guy

I do insulation in Massachusetts lol this video is geeked but it’s solid 😂 from now on I’m just sending this to any apprentice

Thanks🙏. Where did you get it from? Plz upload all of them.

Does anyone know where you can still find any of this material I need to find some to go on an older home

By the way, in Florida you need a permit from the communist county dictators to do anything to your home. That includes any work done to windows, doors, or yes, siding. I am surprised a permit isn't required to hang a picture inside on your wall. I highly doubt the county would approve of that technique of replacing a section of siding. You need an engineering drawing, zoning and work permits to do any work, which makes repair cost twice as much. A simple small job all of a sudden is an unreasonable cost to do. No wonder homeowner's insurance is so high. One has to do the work on the sly, at dusk, or over night, and hope no nosy neighbors report you. Then pretend it already looked like it does now. Yes, I had a nasty experience with the county. I previously did't know the county had their own gestapo squad with brown suits, ready to fine you thousands if you don't play their game.

I used a paint can top remover hook tool to get the siding off. Worked great for vinyl siding. Should work for Al.

This video saved my rear end. Thank you.

I have a house built in 70’s that has aluminum siding. A tree branch tore a hole in two pieces (10’) I can’t find the pieces at Lowe’s.

I made this video because I was the only one who can figure out how to do this back in the day and some sneaky bastard recorded me and then posted it online

This is me in the video. Not sure how this happened. I don’t concent lol

Good video with so much helpful information 👍. Thanks

Terrible audio

Great video. So it is possible to use vinyl siding to replace missing aluminum piece? Would the grooves fit?

Filmed with a potato? Only sound on one side.

For some reason, no siding company in Toledo Ohio knows how to replace aluminum siding pieces without having to do the entire wall

zip tool 👍

This is a gem on TH-cam. Thanks to both of you for making this.

hi ..as we know, the moisture inside the refrigerant system can damage the compressor..So, how to identify if there any moisture that exist inside the refrigerant system?? is there any alternate prevention or method to avoid the moisture from damage the compressor from the early stage??