วีดีโอ

"Click she's torqued to spec" got me.

I feel like smacking a rusty frame with a hammer is incredibly cathartic.

How did you open it? Removed the screws but it seems glued.

Pain in the ass!

Solid work brotha

What kind of hose did you use to extend the vent hose to the top in the engine bay? Like diameter etc. also what kind of barb fitting did you use? I want to try to replicate this on my car it could save me a ton of money not bringing this thing to a mechanic who might mess up my cats

👍👍👍👍🇺🇦🇺🇦🇺🇦

The capacitors being on made me laugh 🤣🤣🤣

The one I’m doing is even worse. Where that one is thin and almost broken. Mine is broken. I had to be careful not to hit the gas too hard getting it home. And I don’t have a lift😢. But the price was right and the front was either already replaced or washed better. 😂

Hi everyone . Maybe my experience can help some of you. From time to time my SB400 got muted. I can disconnect it and then connect with som other devices but there is no sound from soundbar. I think this is issue when you do not disconnect soundbar from device and try to connect with other device while bar is connected on some other device. For me it helps to take soundbar out off my hose and out off range from my devices. Suddenly soundbar works again. I am quite sure that problems starting with paring with my iMac . Try it before you start with other operations.

Have they been holding up good? Looking to do the same fix myself.

Did you end up making a follow-up of separating the transmission from the engine?

My car was just diagnosed with this problem. I had a grinding type noise that they thought were bearings to begin with. It didn't end up being those. The grinding noise at first would come and go. It would make a grinding noise as something went around a wheel or it ended up being the axle. We lifted it and ran the car. We couldn't hear anything. So we got somebody inside and revved it up to 45. Immediately I could hear the noise. It was coming directly from the axle area. Right underneath where the passenger would be sitting. The outside of the bearing that was not supposed to be moving was spinning around so we tried to tighten it but it did not help. It still making noise. So now I'm looking at tips on how to replace it. By watching the video I was thinking maybe a piece of PVC a little bit bigger than the axle might have been better than beating on the bearing to put it back into place. I'm just worried that I'll dent the bearing and it won't spin. I was originally thinking the other bearing on top of the new bearing but then you would have to try to get the old bearing off again. So that brought me to the PVC idea.

Would anybody know how to do so in 2015 MKC ? I’ve been looking but no luck.

Dude thank you

Couldn't you get that out by taking the bottom 2 drawers out?

Thanks for the video. Given there is a thermostat in the tranny, is the transmission temp the same or lower? Also, cutting off the shoulders of the two steel lines eliminates the hose obstruction. Run the hoses 6 inches over the steel line and clamp.

They are made in Taiwan

Great video! Encouraged me to keep my MKT!

Great job! Probably the youtube video on the entire internet. I am planing to do mine next weekend. Fun fact, the bekt tensioner cost now like 140 $ from rockauto, from Ford dealer $200!

Very cool, So if I was to flush & refill the transmission using the transmission hydraulic pump, breaking these lines would be the place to do that? After cleaning trans pan, magnet, & replacing filter, gasket, etc . Then refill & run approx 3 Qt. Out of hose at cooler & refilling the transmission each time using the start/ stop engine method of pushing new fluid through the whole system?? That should be able to replace all the old fluid?

Hi! I just ordered this unit bc of your willingness answer questions. I had some inquiries, but I scrolled through the questions and comments and found what I was looking for. Thumbs up and new subscriber😊 thank you, sir!

Thank you for this video my subframe has just rotted out and im ready to do this job cheers this is so good to see best wishes from across the pond in the uk

I don’t know if my last comment came through, but I just wanted to say a massive thank you and you’re an amazing person for sharing this

Did you buy that piece that is the front of the rocker panel? The front cab corner if u will? Or did you make that?

This is good to see. I've got to rebuild that entire area on my 71 so getting to see how ur going about it is great for me! Good work man!

open the drain plug when filling till you see fuid to vent the case

My boyfriend's in the process of attempting to remove the chrome finish on the grill and paint it black. After this video, I think it's better to just scrape the chrome finish off, clean it and cover the bumper without removing it. Definitely do not want those clips to break off during disassembly! Thank you for the informative video.

i just can't get that bastard of a plug to get off on the differential. Great video regardless, but now im blocked by one stupid clip

Thanks for using a tripod.

So what parts need to be changed for this repair?

Watched the video twice to check what size hose you are using?? I am guessing it is 1/2 inch hose, please let me know if it is a different size..thx

That is AWESOME!! Thank you for the video, my coupler rotted through with 60k on a 2014, what a garbage design, would have probably spent a small fortune at the trans shop but thanks to your video and time i can repair it now myself..Again Thank you!! Cheers

what size cam

Excellent video with great attention to detail and great camera shots. Clear and concise commentary! Thanks for posting!

That’s a nice seat lmao

So because of those 2 voltage regulators the sub won't work as well?

Any tips on doing this things I need I've got a 2011 jeep compass I'm going to be doing this on please any help and what tools do i need

Hi. Thanks for the great video. How did this turn out when the car is running? Is this car still a 6v or upgraded to 12v system? Thanks!

Planning to buy this. I have an Alpine system thst came with my car. I want to plug this directly to the Alpine head so when i turn on the igniti9n this also turn on and when i shut off the igniti9n, thisnalso shuts off. Hopefully that should work right? I dont have an amp. Just the basic head unit and 2 speakers, front and rear each.

How do I open the soundbar 🫢

great video, what size fill hose / barb thx

Thanks!!!!

So do i still need to have my amp powered to the battery as well? Amd the ground grounded? Or is this bt reciever powering and grounding my amp as well?

Hello. Im looking for a similar fix, going to do my 2011 as a preventive matience got my gates hose from napa and some gates constant tension clamps. Wondering how this has held up ? Thanks

This was great, thanks. You know that POS vehicle's not even worth the repair though right? You just did it because you love this 💩?

Is it manual?

Great job, thank you❤❤

Looks come with oil spark plug

After market manifolds for these 4.6 will only last 2 to 3 years, they don't make oem anymore,, i been replacing mine on warranty,, if you are planning to keep vics,, marquis, towncars, mustang F 150, get ready for this repair periodically,,, bad design to put intake and coolant ports next to each other separated by a gasket they know is going to fail