วีดีโอ

my pegs were super worn down and i couldnt get grip, video is super helpful.

Great tip!

Put the Euro bars on and it will be MUCH better.

I saw on another video there is a restrictor in the exhaust where joins the engine. Was a fair size washer but was very restricted. If kids aren't just learning can take it out.

Is this pittrace cuz I go there alot

Great video, I recently put a down payment on new 2023 CRF300L, I plan on doing this and packing the steering bearings before I even ride it. Is there anything else to check and grease like the wheel bearings, or are they sealed.

Steel bikes & iron men.

Full Floater!!!!!

pwonly sucks did you actually get the parts you ordered?

Boa noite este triângulo da minha 250r 2008 quebrou 😢😢 e não estou conseguindo achar

Hi there, are you going to get new jets to suit the 60cc? Notice much power difference?

Burn it out with a torch is the right way to do it, you will get every kind og dirt out, same goes for the front exhaust.

Oem head is 120psi the eBay head is 100psi

Bud change the head to oem head it’s 120psi the eBay head only 100psi - you welcome hello from Sydney Australia

Throttle cable might be the issue with full rev.

Where can I get the tool?

Voice sounds like chris prat

Its better if you put the piston in the cylinder 1st then put the cylinder on the studs then put the wrist pin in.......

Love the plastic seat spoiler..is it stock..

Is the rear tail light bolted to the black plastic?

Link to kit

Those should of been JIS screws instead of phillips

What is the brand to those bars?? I just picked an 83 yamaha, and I want to change oit the bullhorn bars for something else

Did you chamfer to ports and check ring end gap? I have done about 80 of these cheap kits and they are all over the place on ring end gap. And non have the ports chamfer. And then check squish. That too is all over the place. Anywhere from 3mm to 1mm. 1 mm is best.

That's a sweet garage! Nice change out! - I put Rental low rise - basically looks like the ones you did- I am running into some slight cabling issues since the last owner had the cafe slammed bars and did all the cabling to match.

Try a can of cheap oven cleaner, an old toothbrush and lots of hot water. Spray it down, let it sit for 5 min, scrub it with the toothbrush and rinse it off. Spray, scrub, rinse, repeat. Just be careful of the fumes.

I was hesitant to continue watching...'cause your camera set out of focus, or is it my eyes, lol. Anyway, good quick tips on tools. I wish I had the skills/experience to piece together the bikes you have from frame up. Will watch your other videos.

I actually took off the handle bar off my suzuki gs 750 and swapped them out with the xs 1100 yam bar. Made the suzuki a lot more comfortable .

Brey hill!

Ballegary for me!

You kinda look and sound like Chris Pratt.

Nice video. Did this solve all the issues you had with the PW not revving out properly?

Thanks for watching! Subscribe for a chance to win a XJ600!

Good work!

It won't pull you around. To heavy. Even with a top end it won't do it unless it's a pro Flo or something.

Can I ask what you did to fix the issue with the PW50 not revving out completely? Did a top end rebuild fix that? I have the same issue with my son's '01PW50. It ran great for my 2 older boys then lost power at WOT all of a sudden....just never hits the powerband like it used to. Trying to get it back in order for my 5yr old son now. I tried the following so far-- cleaned carb, clean petcock, replaced exhaust header and silencer, new spark plug, blocked off oil pump.

Hi, just bought one to my son. Its a 2019 model. Have the same sound ( piston slap) as yours had. Do you mean that is OK if there is piston slap or do you recommend to rebuild the top end?

I like the original handlebars ,but seems your son thinks he has a corner on cool ! 😂

Did you pull the governor screw out?

man that ga damn wrist pin!!! in the time it took me to install it I could have done 12 car piston sets haha.

him: says they run through anything me: what about my pw50 and getting it wet it just stops

When a 10 year old just passed you on the outside

What bars did you replace these with? I'm in a similar situation and those look just about perfect for my frame.

34 Millimeters ! , how stupid can you get, that equals 1-11/32" you need to learn metric measurement. You just measured CENTIMETERS, which is about 13-3/8" approx.

Just a tip for you, when trying to remove the shocks , with the bike on the center stand, use a long lever under the rear tire and slightly lift to take the weight off the shock, it will easily slide off, and instead of banging the bushing with a hammer, apply a little smear of white lithium grease and squeeze it with a bench vise until its fully inserted in the shock, also apply a little smear of grease on the shock mount stud to lube that as well. And when your finished be sure to wipe away any excess lube that may squeezed out in the lubricated areas. Good luck, your still learning!

That car would be dead to me

Yikes

Nice video!

Part 1 👉🏼 th-cam.com/video/Pbdz6CBq068/w-d-xo.html