Yanmar nozzles are easily the highest quality pintle nozzles on the planet. Have serviced many many 100's of them over the last 40 years and they really only need replacing when they have been fed water mixed with diesel. Biggest issue with Yanmars is when they get reinstalled and thinner than factory backleak washers are used. The return rail bolt goes deeper into the injector and will actually touch the adjusting shims and boots the injector pressure well beyond the factory specified 160-175bar opening pressure. For a long time now I put all the return bolts in the lathe and remove approx 1-2mm from the end of the bolt.
Where do you get the shims to sit the pressure and what size are they? I have looked for yanmar injector pressure shims but unable to find them anywhere. So could you please advise me on what size shim to buy and where to buy them and what to exactly call them to find them on the internet?
AS A OWNER OF 2400 & 7500 bhp TUGS WITH YANMAR ENGINES we are searching for yanmar M220EN 1200 bhp medium speed we are in India & singapore Dubai , fujairah email :seaworthy@vsnl.com
My Yanmar YM135 is smoking on one cylinder and has the block heater plugged in to start. New injectors are about $90 each. Mine are Yanmar CH14620 injectors. What would charge to test and service if needed. Thanks.
Yanmar nozzles are easily the highest quality pintle nozzles on the planet. Have serviced many many 100's of them over the last 40 years and they really only need replacing when they have been fed water mixed with diesel. Biggest issue with Yanmars is when they get reinstalled and thinner than factory backleak washers are used. The return rail bolt goes deeper into the injector and will actually touch the adjusting shims and boots the injector pressure well beyond the factory specified 160-175bar opening pressure. For a long time now I put all the return bolts in the lathe and remove approx 1-2mm from the end of the bolt.
Do you sell the adapter fir this injector to fit on a pop tester? thanks George
Where do you get the shims to sit the pressure and what size are they? I have looked for yanmar injector pressure shims but unable to find them anywhere. So could you please advise me on what size shim to buy and where to buy them and what to exactly call them to find them on the internet?
Grrrr, reconditioning the nozzle is specifically why I wasted my time watching this.
That doesnt make sense
@@joegunz at all
What do you charge to rebuild plus parts yammer 3 cylinder
Awesome . If u found this video researching the same stuff I am . This really helped for real .
WHERE ARE YOU LOCATED?
243 Sw 33rd Ct Fort Lauderdale FL 33315
excuse me, i wanted to know if you could kindly help me to get a yammar M 220L-UN manual or if you could say to me where could i get one
Thank you
Yall rebuild 1gm10 high pressure pump?
AS A OWNER OF 2400 & 7500 bhp TUGS WITH YANMAR ENGINES we are searching for yanmar M220EN 1200 bhp medium speed we are in India & singapore Dubai , fujairah email :seaworthy@vsnl.com
whats the knob for on the nozzle tester??
He’s there to push the lever down.
OMG 😂 😂
You did a great job with this. I wish you would have done more.
Have you got a smaller shirt???? That looks so uncomfortable!
6CX intercooler turbo injector nozzle if you can help me
Painful to watch
It runs between $ 140.00 to $ 250.00 dollars per injector. Please give me the two letter code on the injector and give you a better estimate
My Yanmar YM135 is smoking on one cylinder and has the block heater plugged in to start. New injectors are about $90 each. Mine are Yanmar CH14620 injectors. What would charge to test and service if needed. Thanks.
@@sdwputnam did you pull your injectors out yet?
@@sdwputnam New is $90 and reconditioned is $140 - $250. Do we have our thinking caps on?
how much does the yammer hammer injector job run per injector
Your shop is remarkably clean, organized, and well equipped