Direct Amazon link for items-
www.amazon.com/shop/dnicolebeauty/list/2A39GRYLJ4NM9?ref_=aipsflist
Other items listed:
Home Depot:
BrassCraft 1/2 in. FIP x 1/2 in. FIP x 20 in. Braided Polymer Faucet Supply Line B8-20A F - The Home Depot
Handprint 1/4 in. x 2 ft. x 2 ft. Sanded Plywood Project Panel 300810 - The Home Depot
Swivel wheel-Everbilt 2 in. Black Soft Rubber and Steel Swivel Plate Caster with 90 lb. Load Rating 49477 - The Home Depot
Swivel wheel with lock- Everbilt 2 in. Black Soft Rubber and Steel Swivel Plate Caster with Locking Brake and 90 lbs. Load Rating 49509 - The Home Depot
Stationary wheel- Everbilt 2 in. Black Soft Rubber and Steel Rigid Plate Caster with 90 lbs. Load Rating 49481 - The Home Depot
Everbilt #8 x 1/2 in. Phillips Flat Head Zinc Plated Wood Screw (12-Pack) 807221 - The Home Depot
Walmart:
Trash can for waste water- www.walmart.com/ip/14170566?sid=79bb6337-620b-4c50-964d-e10294fb6635
Trash can for clean water- (Walmart)- www.walmart.com/ip/775305647?sid=e412cba4-711e-43b9-881b-5ecc5af87e20
Table- www.walmart.com/ip/39131547?sid=31429758-464b-433e-a542-7a1a7fb80703
Step 1: Preparing the Brass Fittings
1. Attach Brass Pipe Fittings:
• Wrap plumbing tape around the threads of each end of the intersection brass fitting.
• Attach brass pipe fittings to both ends of the intersection fitting. This prevents leaks.
2. Attach the Brass Assembly to Water Pump:
• Position the water pump facing you.
• Attach the brass assembly to the left side of the pump (even though it appears on the right side in the video). It is crucial to attach it to the correct side for proper water flow.
Step 2: Adding the Strainer
3. Attach the Strainer:
• On the opposite side of where you attached the brass fitting, connect the strainer.
• Don’t forget to wrap plumbing tape around the threads before attaching to prevent leakage.
Step 3: Connecting the Water Lines
4. Hot Water Line:
• Wrap plumbing tape around the hot water heater’s threads.
• Connect the hot water line to the hot water heater.
5. Cold Water Line:
• Take the additional 20-inch faucet supply line.
• Connect one end to the right side of the brass intersection fitting.
• Connect the other end to the cold water input on the hot water heater.
• Use locking pliers to tighten all connections securely.
Step 4: Setting Up the Diaphragm Pump
6. Attach Filter Pieces:
• Connect one of the black-and-white filter pieces to the diaphragm pump.
• Insert the clear vinyl braided hose into the filter. This hose will draw clean water from your water supply into the pump.
Step 5: Building the Mobile Base
7. Cutting the Boards:
• For a large trash can (clean water): Cut a board measuring 20.5” x 14.5”.
• For a smaller trash can (waste water): Cut a board measuring 14” x 17”.
• Use an electric cutter if available, or get boards cut to size at Home Depot for free.
8. Attaching Wheels to Boards:
• Each board will need:
• 2 stationary wheels (fixed position)
• 1 regular swivel wheel
• 1 locking swivel wheel
• Use wood screws (#8, 1/2 inch recommended) to secure the wheels in place.
• Drill wheels into each corner of the boards.
Step 6: Testing the Water Supply System
9. Connecting Water Supply:
• Fill the 20-gallon trash can with clean water.
• Place the high-pressure braided hose into the clean water supply (trash can).
• Ensure the waste hose is positioned inside the waste trash can to catch used water.
10. Adding Weight to Hoses:
• Cut a PVC pipe in half.
• Attach one half to the clean water hose and the other to the waste water hose to keep them submerged and secure.
Step 7: Powering On the System
11. Power Connections:
• Plug in the hot water heater and diaphragm pump into a power strip.
• Switch on the power strip. You may hear a temporary noise until the pump fills with water.
12. Heating the Water:
• Allow the hot water heater to warm up for 25-30 minutes.
• You can turn off the water flow while heating, and it will still warm up.
• Once the heater has warmed, turn on the faucet to the hot water setting and check the temperature (adjust heater settings if needed).
Step 8: Final Testing
13. Testing the Sink:
• Turn on the faucet to ensure water flows correctly into the sink.
• Confirm that waste water is draining properly into the waste trash can.
• Ensure all connections are leak-free before using the shampoo bowl for clients.
Tips & Reminders:
• Always use plumbing tape on threaded connections to prevent leaks.
• Use locking pliers for tightening to ensure secure fittings.
• Check all hoses are securely in place before turning on the pump.
• Be cautious with hot water settings to avoid scalding.
Now, your portable shampoo bowl setup should be ready for use!