I have 2 exact esc's with the same issue. The esc is having issues the current placement. 4 poles have to be energized in a timed fashion. For whatever reason usually due to excessive heat or stress the esc has damaged the timing mechanism and is now junk. Unless u want to give it a push start every time u take off. Lmao
I just got this setup and it’s doing the same thing , I have the program card but I don’t want to mess with anything, if I don’t even know what to change
U need to calibrate the esc. There is a set button under the power on button. Press it while turning the esc on. Wait. The LED turns Blue. Hold full throttle. Esc blinks red, beep. Now full brake position, beep beep. And now neutral, beep beep beep. Calibration ✅. Turn esc off and back on. Now it should work.
Have you found the problem with acceleration or start problem? I have only this problem. Ever. If I press forward or reverse the motor makes tick tick tick and then it will start with acceleration
@@christiansrcs7789 bro its not the motor. I can recreate this scenerio down to the transmitter to show u what it is. No offense just dont want to mislead him but honestly hes prob already burned up a couple brushed motors by now.
I HAVE THE SAME ESC SET UP, WHY IS RESPONSE SO LAGGY AND GLITCHY
Same problem with mine just got it last week any idea how to fix?
Made in china
Because it's GARBAGE
Just spend the extra money and get something that u know is going to work u can't cheap out on some things
You need to change your tune
Trim*
How do I recalibrate the ESC does anybody know how to do it please let me know thanks
made in china!!!
I have 2 exact esc's with the same issue. The esc is having issues the current placement. 4 poles have to be energized in a timed fashion. For whatever reason usually due to excessive heat or stress the esc has damaged the timing mechanism and is now junk. Unless u want to give it a push start every time u take off. Lmao
The esc is garbage.
I just got this setup and it’s doing the same thing , I have the program card but I don’t want to mess with anything, if I don’t even know what to change
Hey i have a solution.
U need to calibrate the esc. There is a set button under the power on button. Press it while turning the esc on. Wait. The LED turns Blue. Hold full throttle. Esc blinks red, beep. Now full brake position, beep beep. And now neutral, beep beep beep. Calibration ✅. Turn esc off and back on. Now it should work.
calibrate it by holding throttle fully and turning esc on it should beep twice, then turn off and on again
My esc is on when i was take it high it was properly work but i run in ground it will not run when off and it wil work
pinion gearattached to motor is too high find one with less teeth
@@db-iv7tz that will have absolutely 0 effect whilst the motor is on the bench and isn’t attached to any other gearing.......
@@connectionlost1063😂. These people crazy lol
motor power cable torn from the pole, but not completely
It's the cables
Have you found the problem with acceleration or start problem? I have only this problem. Ever. If I press forward or reverse the motor makes tick tick tick and then it will start with acceleration
אני יודע שאני כותב לך אחרי הרבה זמן אבל נתקלתי עכשיו באותה הבעיה ואם אתה יודע את הפיתרון אשמח לישמוע..תודה.
Set your throttle range to high,its on top of the controller,then recalibrate
Mine started doing the same thing after I changed motors
What's the solution. I have the same problem. What result did you get
His esc is probably trash just get a new esc
@@christiansrcs7789 bro its not the motor. I can recreate this scenerio down to the transmitter to show u what it is. No offense just dont want to mislead him but honestly hes prob already burned up a couple brushed motors by now.
@@06heify oh now that you say that lol I see what I said wrong 🤣
Does anyone no how to programe one with no card?
it not possible to do so
only with a hobbywing esc is possible
I programmed it with the card still no throttle
@@Lailajohnson123 change your trim in the middle should be your throttle trim
The ESC doesn't seem to be self calibrating the right way. When you turn it on you should hear that jingle noise twice in a row.
I also have this issue
I have a similar issue did you get it resolved I suspect mine is a faulty esc
It had no program features crappy esc got refund and replaced with a hobby wing
@UAE RC'S what's soft mode ?
@@peterfantom7877 hi what hobbywing esc did you get to replace it
@@adamkhan8003 I returned the whole bundle and went with a brushed system in the end fitted a 1060 with a brushed motor and have had no issues since.
Did u ever sort issue, what was wrong part