![GTJD Restaurant Tech](/img/default-banner.jpg)
- 60
- 147 830
GTJD Restaurant Tech
United States
เข้าร่วมเมื่อ 1 ต.ค. 2012
This channel will be based on my experiences as a technician. I'm a HVAC-R tech who also works on Restaurant cooking equipment (aka hot side), some plumbing and some electrical. I'm the guy who trains all the new employees. I decided to start a channel to post helpful tips, tricks and guides for them to reference if they get stuck on a job or want to prep for an up coming job. These are "real life" videos, not that fluff that manufacturers show when they are testing new equipment in a clean environment...
Please, if you are not a service contractor/technician, do not attempt what you're about to see. We have training, licenses and insurance to cover ourselves in any event, keep that in mind.
If you appreciate my videos, you can show your thanks by hitting the link button and subscribing/following.
Please, if you are not a service contractor/technician, do not attempt what you're about to see. We have training, licenses and insurance to cover ourselves in any event, keep that in mind.
If you appreciate my videos, you can show your thanks by hitting the link button and subscribing/following.
testing the ice o matic bin stat
testing the bin stat or also known as the bin switch on an ice o matic GEM nugget ice machine
มุมมอง: 116
วีดีโอ
EEV (electronic expansion valve) solenoid magnet test
มุมมอง 15928 วันที่ผ่านมา
EEV (electronic expansion valve) solenoid magnet test
how to tell the age of a Lennox RTU (rooftop unit).
มุมมอง 48หลายเดือนก่อน
how to tell the age of a Lennox RTU (rooftop unit).
Drain freezing on True TUC reach in freezer
มุมมอง 85หลายเดือนก่อน
Drain freezing on True TUC reach in freezer
captive air fireye fuse
มุมมอง 2225 หลายเดือนก่อน
while replacing this fireye, it reminded me of a job I did years ago and I wanted to pass along valuable information.
Absolute Aire Make up air walk through pt. 2
มุมมอง 2396 หลายเดือนก่อน
In this video I go over air pressures and how to adjust along with some other useful information. I make these videos for my self, my team and to help folks in the field. I have one speed, it's, "Get The Job Done"These videos are not intended to replace trained technicians. I post them to just give advice to those who may not have seen these situations before. Please call you're local contracto...
Traulsen SER-60711-05 KIT MIT TO NGC RETROFIT
มุมมอง 5188 หลายเดือนก่อน
Converting Obsolete Traulsen MIT relay and controller to the updated NGC retrofit controller kit traulsen ser6071105
Rooftop heat exchanger inspection
มุมมอง 1989 หลายเดือนก่อน
this heat exchanger will take 2 to 4 people to inspect it correctly. This is only one way to get the job done.
Ice o matic cleaning 2.0
มุมมอง 8579 หลายเดือนก่อน
just me showing my guys how to clean an Ice-o-matic pellet/nugget ice machine based off the manufactures guidelines. Music: www.bensound.com/royalty-free-music
Soda pop dispenser ice bin *SAFETY FIRST*
มุมมอง 26210 หลายเดือนก่อน
Soda pop dispenser ice bin *SAFETY FIRST*
Lennox roof top unit condenser fan cycle
มุมมอง 27210 หลายเดือนก่อน
Lennox roof top unit condenser fan cycle
Refrigeration condenser recirculating hot air
มุมมอง 18211 หลายเดือนก่อน
Refrigeration condenser recirculating hot air
reach in cooler flooding liquid back
มุมมอง 1.7K11 หลายเดือนก่อน
reach in cooler flooding liquid back
Lennox RTU low pressure switch on high side lines
มุมมอง 1.5Kปีที่แล้ว
Lennox RTU low pressure switch on high side lines
pitco m#SRTG rethermalizer automatic water fill issue
มุมมอง 366ปีที่แล้ว
pitco m#SRTG rethermalizer automatic water fill issue
Lennox rooftop unit Heat/AC test short cut
มุมมอง 8Kปีที่แล้ว
Lennox rooftop unit Heat/AC test short cut
Built in Delfield refrigeration temp probe replacement
มุมมอง 1.4Kปีที่แล้ว
Built in Delfield refrigeration temp probe replacement
Part 1 of HVACR tech comedy DO's and DON'Ts
มุมมอง 2652 ปีที่แล้ว
Part 1 of HVACR tech comedy DO's and DON'Ts
Captive Aire Make up air Fireye retro fit kit
มุมมอง 8072 ปีที่แล้ว
Captive Aire Make up air Fireye retro fit kit
Absolute Aire Make up air walk through pt. 1 - Ignition controller and modulating valve
มุมมอง 2.2K3 ปีที่แล้ว
Absolute Aire Make up air walk through pt. 1 - Ignition controller and modulating valve
This is not the case in every brand contactor. In the new ones I have, there is no way to convert it like you did. You should have said YMMV to be more accurate.
How much should this job cost ?
Did he say he had to jump off a binswitch to another binswitch?
Okay so I have a client that had a small grease fire in the kitchen and the ansul and sprinklers went off and one of their breakers won’t turn back on, guessing it’s a shunt? They have a weird frame covering the dead front, I have dealt with Siemens load centers a million times but I literally can’t figure out how to get inside the panel
Good job 👍
thank you for no annoying music. I hope your channel does well
Why not just rub the marker on it?
If it works for you then that's also a good way. I personally have better control over my finger with some marker on it than I do the marker itself. If you get too much marker on it, then you may have lost the ability to see the raised numbers and letters. It can blend in. Practice using the marker on a part that doesn't have useful info, if that's your preferred method.
Now that's a winner of an idea!
The bushing got a grub screw holding it onto shaft?
How do you get a Retrofit kit for going from the lens to flame rod?
Brother I can’t even figure out how to get the fucking blower compartment open the latches don’t do shit
Ya that design sucks. Always issues with freezeups
Thank you for a good video :) Few questions, my pump is leaking from the shaft seal. What is the correct size of the seal and how do you remove the old seal and put new one in? Also, at the same time the o ring to the back cover should be changed. Do you know what size is the back cover o ring? One more, the pump motor is seized, it 's full of hardened grease. How does one remove the pump motor? The electric connections?
Damn 77💀💀💀
Love the energy man🔥😂
Are you using a standard cat 5 or cat 6 cable between the vfd and screen?
Cat 5 and cat 6 are the same other than a cat 6 is made in a way to be more resistant to interference. So you can use either. The one I used in the video of cat 5 though
Ok perfect! Thank you for your response because I lost the little connector it comes with and didn't know if that was a priority connection.
I didn't know what direction the air was moving just from the video but "some guy just replaced a thermostat and it isn't working now" usually means "the thermostat was not installed correctly". That and the bulb seemed out of place.
Are you checking micro amps for flame rect?
Hey sir I have a issue with the same fryer but only 2 tanks. How ever it keeps making a loud popping noise. I changed out blower motor and relay as well. What else can it be ??? Pls help
Check your gas pressure
Just what i was looking for! Thank you.
Great refresher More please and thank you sir!
Wow thats an old unit still high tech for some back them
Thanks for the info My drain limit switch was faulty
My y600 oven stopped heating up in the middle of dinner,the pilot is still on but no flame? Please help
Thank you
Life saver thx
No way!!! What??? I'll check this out definitely
At first I was skeptical reverse wiring the polarity of the motor. After trying to get the backside of the impeller motor off (with no avail). To spin the shaft, we decided to have staff empty the vatts so we could undertake the nasty job of pulling the motor. We ran across your video and said-what the hell, we will give this a whirl as the wires were accessible through the access panel on the front of the motor. After reversing the wires and a few quick on-offs! Viola!!!! The impeller freed up and we are back in business! Thank you so much for posting this detailed video.
Forced draft
As a new hvac/r tech thanks my dude
Thank you, got this unit working after watching this ! 🙏
Thanks for the help! Do you know what kind of power opens the combination valve?
keep a empty bottle in your bag😂.
Bet unit is more problematic now tho
Just want to express my gratitude for this video that you put up. Had to replace the gearbox assembly last Friday, and I've never done one before. Thanks to this video i was able to swap it out and get it running again. Once again, thank you.
Excellent very very helpful thank's and a great site by the way...good humour and fun.
Hi ,I shut off my water for my restaurant for couple days ,after the ice o matic ice machine no water come in the reservoir , please help for!!
The sound effect was flawless.
Your comment made my extra editing worth it!
I found I had a problem with my gas line! That could be an issue too.
Great video sir, please give more details about this captive air unit.
Great video! I was wondering if you can help me out. I am trying to run power to this unit. My unit is a 208 3-phase. The unit specs that I run 3 hot wires (black) 1 neutral (white) and 1 ground (Green). Max amps is 15 so I am going to run a 3 pull 15 breaker. My unit has an added option of DCV-SF1 that requires a red wire to be hooked up also. My question is where does this red wire go? The black, white and green wires go back to the panel and are hooked onto the breaker. What am I supposed to do with the red wire? Does it go to the hood control unit. What even is a DCV-SF1 ?? Thanks!
I won't be able to answer your question fully since I'm not the manufacturer and this is a new install. The DCV should be a remote display that you use to toggle on and off the equipment. To use or bypass that remote should be in the wiring diagram. There are a few variations and I don't feel comfortable giving advice on an install that isn't under our company's license and insurance. You will need to get ahold of the manufacturer
Talkin about a bit below beer can cold
Dzięki za film, ale ten agregat wygląda jak by ktoś w garażu to składał. Jak można coś takiego komukolwiek sprzedawać.
Very detailed video ! Im a tech i work on restaurants and dont get too much experience with MUA units and this explained em very good. Thank you and i look forward to your videos. Are you located in the state of michigan?
Yes, I work in michigan. I have an updated video on make up air as well
Good fun with excellent knowhow thanks
Perfect thank you fof this superb tutorial which is very helpful.
My N word ✊🏻 Thanks for the lesson.
I didn’t know the controller packs were no longer available. Nice that you can retrofit new traulsen stuff I retrofit dixell controllers though, the traulsen stuff is expensive
Standoffs😊
Don’t forget to check the incoming gas pressure too