วีดีโอ

Do you have any advice on how to properly wire a dimmer switch to a single Alpena 15" Terra off-road light bar? Any special preparations/care that I would need to take? What is my simplest and most economical route to take? Any advice would be much appreciated... Thanks!

Can't find the kit

Where do you get the kit

How did you remove the rear seat in the expedition XP 5?

Just wondering if you took a decibel reading before and after the sound/temp was fitted, ?

man that carpet is going to collect so much dirt and dust....and vacuum can only get so much...just IMO for Az

I used your video today to wire two Rough Country LED light bars each of which came with their own harness that included a relay but was designed to connect directly to the battery terminals. I wanted to connect each to the Polaris Pulse accessory bar and take advantage of the switched power to avoid battery drain. I removed the ring terminals from the positive and negative leads from each wiring harness and connected them with butt connectors to the red and black wires of Pulse bar pigtails. I then followed your instructions to remove the control wire from the relay where it was connected and reconnected it with a butt connector to the blue wire on the pigtail. After ensuring that everything worked as desired I heated the heat shrink tubing over the butt connectors and zip tied all the extra wire from the harness. I also added some labels to help me keep things straight as I add more accessories. Thanks for the great tips and easy to follow video!

Did you build this kit, or can a person buy it

I can't fond the video of the putting sound dampening on the rear

What do you do if you have a power windshield washer installed will this still work

Will this work as a heat shield? My 21 commander gets so freaking hot in the cab and Id really love to use this as a solution if it works, Thank you!

Looks like nice material. I have a defender max limited, im wondering if besides behind the rear seats if i could put it in the engine bay from the other side too at the bottom. Biggest issue is if getting it wet would cause it to come off? Thanks for the video, exactly what i was looking for!

I do notsee these on your website?

Are you connecting your fuse to the pos battery and the modified switch wire to your key? Also, what wires hook to the 5 pin switch?

Is it available for the RS1?

Hello, I did get the expedition floor mats from you so now I bought the ranger XD 1500 crew cab is there a possibility you’ll be coming out with those floor mats I would be happy to buy a set

Ordered a complete kit including the acoustic pads. Hope it helps!! Had the polaris clutch recall done as well

Should have had someone else video this. Never saw under seat

What uppers are on your buddies XP4?

Great video, thank you 🙂 This worked great, except ☝️ Im trying to hook up 2 switches - front light/back light. My problem is both switches turn on both lights. Im pretty sure its how the switch bank is jumped together but idk. Any ideas? I have 2 switches just like the type you show here (should there be a disclaimer on this video "for single switch only!" ?)

Would it work for a headliner? Just added my roof and now we can't have a conversation without yelling. Also what about water and dust?

Hello is this still available to purchase? Also will it work on a polaris general xp 1000 limited?

Any reason you can't use the carpet kit as a template?

With everything that you have for the xpedition, how much differance will it make with the noise?

Yeah light works but where is the day time light wire and turn signal from rzr 😂

Stock Xpedition cab noise is around 85db cruising speed using decibel app on phone. Did you check what yours is with sound deadening kit?

How many sheets of the sound deadening mats are needed for a xpedition xp 5

There's two bolts on each end of the seat frame and two in the middle and that whole seat frame lifts out in one piece. Probably much easier than removing just the back.

Thanks for this video! I've been trying to figure out how to jumper to just accessory power for my ranger!

Can you only wire up the turn signal wire and omit the DRL?

thanks. Great video with great ideas...

My new Xpedition Northstar XP has a sound deadener carpet on the back wall and rear sides from the factory.

Can u leave these on when parked in the garage without the tires getting a flat spot being foam filled?

is there enough exposed threads to take the weight and pressure?

I installed the wiring kit from niteliite, was prewired basically plug n play, so now I have constant power to the rocker switch and the light on the bottom of the rocker stays lit constantly, ita suppose to go on n off with the key. I have switched the wires around every way possible on the back of the rocker switch to try n get it to work with the key on but no luck. The directions said for the key on was to jump the red wire to the #6 on the back of the switch but that just gives it constant power to illuminate the bottom part of the switch. What could possible be wrong here?

You going to do the carpet kit for Yamaha RMAX 2?

Will this kit work with a 2023 xpedition

Can this be used with the overhead CanAm control panel for the wiper and lights?

Whete do i buy it

How does the it sound

Are you going to be doing a new Polaris Xpedition? Thanks!!

I don't have a Razor, but I'm thinking about doing the same thing to my Coleman Outfitter 400 UTV as it's a little noisy sitting in it.

Do you have any videos on the new xpedition? Thanks!!!

Where can you buy these products

I would have to guess after that carpet gets wet it will probably get smelly

Anything in the works for a Wildcat XX sound deadening kit ?

Does the heat shield come with it I did not see that on the site.

Bad thing is love heat in winter‼️🔥

I wish you could show the back of the switch for reference.

Do you have an installation video of the sound deadener on this commander?