วีดีโอ

Die Anmeldung für 2025 ist nun möglich! 🙂 www.benchrest-germany.de/wp-content/uploads/2024/12/2025-07-Einladung-Word-Weimar-Shoot-2025.pdf

You must be rich if you have such a rifle, enjoy it!

You are truly a kind-hearted person. Thank you for taking the time to record a video amidst your busy schedule. This video has been very helpful to me, and I have probably resolved my doubts

I would like to know how to disassemble the gun stock. Could you please make a video to demonstrate it? Thank you very much

Nice!! Want some Exterieur footage. Give us some coldstart Sounds from the exhausts ❤

Schönes Gerät und auch noch die alte Version. Daumen hoch!

Ihr Benchrester seid schon ein angenehmes Völkchen, danke fürs zeigen...

gerne nächstes Jahr wieder

Great content!! Keep up this nice work!

When applying torque values ALWAYS begin with inner most fasteners and work outwards towards the ends (moves stresses outwards towards ends vs in against the middle and binds/locks stresses in middle). A good practice is to rap rail screws with plastic end of screwdriver or plastic mallet 3-5 minutes after torque to release tension on threads. In aviation maintenance S.O.P. is to torque in 3 increments to final torque value ( e.g. 75 ft lbs final torque done at 25,50, & 75).. 5 minutes after final torque give one last snap on wrench.

It looks like my dry heels dammit

Over heating the barrel doesn’t help damp cloth or a barrel blower to kept the barrel cool does help a lot ! 🇬🇧🏴󠁧󠁢󠁥󠁮󠁧󠁿💪👍

So you're saying that you pushed 4 (or so) patches wet with IOSSO on them through the bore is it make that difference in about 1 or 2 mins or so? Or are you saying that you scrubbed the bore back and forth with patches wet with IOSSO about 4 times? What does "further cleaning in between" mean?

great video thanks

So schön seidig glänzend 🎉

Would love to see an in depth Review ❤

Nice!!

So the tree bark look is the throat erosion

I also use a removable threadlocker (LOCKTITE).

5000 rounds

Hi Stephan, danke für dein ausführliches Video. Verständnisfrage: weshalb muss die Schiene überhaupt gebettet werden? Hat die Schiene auf einer Seite Luft, da sie nicht komplett gerade ist? Könnte man die Lücke nicht durch einfaches festschrauben schließen?

Well Done! Danke für den Tipp. Sehr gute Vorführung.

it is a Mercury/sabatti rifle ?

What kind of distance is this?

WOW!!! Looks like you can cover that group with a dime!!!

Thank you my friend...this version is a vast improvement over the first one I saw....much more detail and more clearly shown also...thank you...yours is the only one (that I'm aware of) that shows the install in up close detail...I was seriously hesitant about disassembling the trigger and not being able to REassemble it properly (my residual weakness on my LHS from my 2002 stroke makes detail work more difficult than it used to be...this video is a lifesaver!!!

Do you re install the safety after the complete linstall or between the trigger and hammer install???

Thanx for the detail...I need to remove mine prior to painting the receivers - I have the (IIRC) JP pin retainers for both sides...will I be able to eliminate the spring retainer during install??? I have difficulty using my left hand/side due top a 2002 stroke and installations liker these become more difficult when pon;y onre hasnd co operates...

Nettes Video... wir haben letzten Samstag zusammen in Oldenburg geschossen.

Thank you very much for the video. Made installation so much easier.

That's a good post thanks man! because if you went by the written instructions you would die of old age. But this is the only post and there's no detail on how its adjusted. and iv had a problem with the safety not working because there's too much movement on the safety arm and that sets it off. for $900NZ I would have thought that there would have been more posts like this to support the product. also I don't understand why the safety arm is tapered off under the safety. long story short this should have fitted straight onto a bushmaster with no issues but there is. sending back for refund. Gutted:(

..this is not easy..the first time..

Mit welcher Waffe und Kaliber ist das geschossen?

didn't realize you could own the evil black rifles there. how difficult was it to get one?

The rifle is made by Schmeisser Germany, model is Ultramatch STS (Semi-Auto) And by the make of my rifle one could guess where i live :)

Thank you for posting this. Where are you and what kind of lower is that?

Thank you for posting this!