วีดีโอ

Thanks alot

How to add pipe branch or tee to do this simulation?

What if heat transfer coefficient is not given & instead of that its mentioned that water with pressure of 3 bar flowing on bar (like cylinder in crossflow) then how can it be modelled in comsol

Can you help me with some designs please?

Can you help me with some designs please?

Can you help me with some designs please?

in schematic their eleviation shown for the 3rd pipe length of 50m , why u have not consider the elevation

Weldon Amir

great thanks

Solo por este video tan aclaratorio, mi suscripción. Muchisimas gracias.

Hello, can you help me of simulation

Great work sir. Keep it up

Informative video sir.. Kindly sir make a video on how to download the comsol and aspen..

Hello. I have a 2D system. There is a vein with blood flow and I want to define biological tissue. For 2D system, I assign non-isothermal laminar flow for flow domain and heat transfer in fluids for biological tissue. Is it correct? Should I assign heat transfer in solids to define the tissue? thanks

Hello. Can you instruct how to simulate a laser pulse acting on skin tissue! Thank you!!!

Excellent video, sir. Kindly bring some videos on 2D axisymmetric simulation of nucleate boiling using phase field method

Hi, can you guide me about passive micromixer for efficient gas and liquid mixer?

very annoying, add voice

Can you please demonstrate Transient Elastohydrodynamic squeeze film interaction in comsol

Can you send me this presentation!!!

Thanks for the video, it was instructive. When would you release the part2?

Hi, can u help me to calculate a heat transfer coefficient for my thesis because i still confuse about this software? I already have the result after run the simulation

Can you please help me in calculating avg nusselt no. In a 3d rectangular channel which is same as the one u have used just its rectangular? In which fluid is moving in turbulence and a constant flux is at base

Thank you for this informative video, I would like to ask, Is it possible to model a Transient HT problem for a an Insulated tank that contains aggregate held in 100 c and see the temperature of the aggregate after 24 hours, in other words what would be the temperature of the aggregate after 24 hours if it was preheated and sent to the tank at 100 C. I appreciate highly if you could suggest something or tip sth in this regards. which boundary conditions may be used in such case, and how to model the aggregate? Thank you in Advance

could you perform optimization for this case please

Hi, you calculated heat transfer coefficient for boundary 4 which is not a wall of flow or fluid?

thnks for this vidio what this name method?

any vedio for newly heat exchanger which we have to design

Hello I have a problem in naturelle convection simulation can you help me thank you

No voice

thank you for this video but i,m working on absorption cycles water/libr via aspen plus and i'm blocked on the fiste step becouse i dont have the flow rate of the water between condensor and evaporateur an i,m worked on low pression so please if you could help me how i can figure out this problem I will be grateful and thank you

sir, I thinked you should record your voice over with it. And my suggestion is that make a basic course of comsol, that how we will known that which model we need to use, which equation will be using etc.

V good dear keep it up

Voice over needed😊

So, what the result value number

May I get your contact email

Wow

Thanks bro greetings from Poland

How to model solid material, but surface of the material will be changing with time based on environment temperature. For different materials the response will be different. For example during when the whether is 5 degC, some materials like glass with time can reach 2 degC meanwhile at same condition other materials like plastic will be between 4-5degC. Thanks

Hello please i have a question could share your email?

Hello nice demonstration using very common question. Can you please tell me why you did "Union" operation. Is that mandatory? What if we don't do that, please explain!

Thanks 🙏

Great video! Thank you!

hello, I have a problem on comsol, I have not found a solution to make a twist by fixing the Z axis

Where did you get the th out?

Can you do a video or send me a link to learn about Simulation and modelling of microwave drying with COMSOL in terms of heat and energy transport!!

Thank you, good example, could you please simulate about solar radiation and solar cell.

Excellent Tutorial Sir.