วีดีโอ

Thank you very much

Hi. Thanks for your presentation. It is really benefitial to early stage electrical design works. Is there any K-factor consideration to generator windings rated to harmonic distortion ? There has been a rule of thumb that if a generator is supplying to a bus which has multiple VFD connected (i.e. non-linear loads) and the VFD drives come with 6 pulse controlled rectifiers, the generator power needs to be de-rated by 50%. In this case, if 1000kVA, 0.4kV generator is installed, the winding can be loaded to 500kVA only if I am not wrong. If you have time, please make a presentation and share in this channel. Thanks.

Very nicely explained, cannot find this information clearly specified in books.

hello sir. what do i have tot change just to see 1 PV modue in all my scopes?

Hello how are you found the values of maximum and minimum duty cycle in the code ???

sir if u really want to get our favourite teacher ...u should consider our needs ...means u have to put the matlab file ....we r used to do work before the one night ....😂😁

I got Nan for my display. What was done wrong?

Sir peak value is higher at 11kV side as at 11kV side if fault occurs then xmer will not be inline. I think if fault occurs at 433side then x/r ratio will come in pitcher. Plz comment to guide me

Thank you so much, i had a lot of trouble for some odd reason and this helped me get it working almost instantly

Can you share the model please

Good and simplistic ways of explaining the problem

how is R2 0.4?

Sir can you please post the videos on "simulation of boost converter for pv system using ANFIS controller using matlab simulink"

How did u choose Vout=500, did u calculate it?

why am i getting nan for ipv and vpv?

Good explain

I tested this simulation but it doesn’t work. there is anyone who could do this simulation to help me, please? 16:36

Sir, can you send block diagram of the topic.

thank you

Hello sir which version you are using

Great !

i try this pv array model the display shows the nan there is no numerical values so how to solve this problem

Hello Sir, I've been doing network analysis for project using ETAP, currently encountered some strange issue of harmonic injection, if you don't mind can you let me know if we can discuss further as I would like to consult you for expert advise

Thanks for the tutorial, but I'm getting output voltage below 500 what to do now?

Hello Brother thanks for the video, kindly make video on Trafo Tapping and its impact on Load flow in ETAP software

Very nice video...clearly explained ❤

hi sir, i want to discuss with you please share your email id or mobile number

Sir, whether 433 v solar system used for power generation connected with conventional drive load at 433 v and main incoming EB utility transformer is 11kv/433 v to feed the load.. is conventional distribution transformer is ok or k rated Transformer to be installed

Thank u. have a good day.

👍

❤

👍

Why it is showing nan value

thanku

Super! Would be really cool if you did on on speech shaped noise application on speech

Sir, could you please give me manual calculation to get the value of impedance 0.27 ohm at bus 7.

thank you so much. Can you please help how to model STATCOM? can we use the same method?

Hello, Could you please help ! This model keeps ending up with "Nan" results in the display for MATLAB R2020a. Any idea?

Useful share

Is the code there correct?

drop off the music!!!

Doctor, if I want to use 5kw wind turbine, what numbers I should to change?!!

Thank soooooo much doctor 💕🌱

I have a question, on minute 5.45 , how do you get those values for the duty cycle, which is the base for that

Good explanation sir. Bt I have a doubt about the diversity factor. How cum the value of diversity factor can be less than 1?🤔 . I guess its demand factor not diversity factor

plz provide me simulink file its not working

Nice Video. Can you provide your mail id

Where i did mistake sir

Nan is displaying in voltage and current

Sir i connected same like you but current and voltage values are not displaying