วีดีโอ

I see this is 7 years ago. My question is why did you mount the radio and transponder in the panel area? I see so many do that and it contributes to massive radio noise. Shield each one with a thin carbon fiber box to prevent this issue along with ferrous rings to cancel any impedance loops in the wiring. Done correctly using carbon fiber (because it blocks RFI) leaves you with crystal clear radio transmissions and reception. I learned this doing radio and CB installs in cars and trucks. The engine puts out all kinds of RFI and you need to shield against it.

Had to stop watching this after just 30 seconds in - dizzying vertigo from all the rapid camera moves.

Hi John. I’d like to borrow your video for a non commercial (LAA) presentation please ?

Nice one JP, what a great day!

I do like that tail camera view. Looks like a great trip 👍😎

2 minutes into the video: I can't understand a word you are saying. Your video is not in focus.

Fantastic journey, footage and scenery, looking to do part of West coast in July

Very nice video John. How do you get on with the 360 degrees camera?

Awesome 😎

Can you please post more flights like this I have just started learning to fly and my ambition is flighs like this

What an awesome trip! Spectacular scenery and looked like good flying conditions. How many hours flying was that?

Superb video. What camera were you using and how was it mounted?

Marvellous, why we do what we do .

Epic 👍

Hi John, this video is a bit old now but thank you so much for making it! So hard to find information about this product from people who have used it successfully. I have a question if I may - is the paper in the kit just plain old waterslide paper theyre using (the one you print on). Because I tried doing the same steps you did in the video above, both with cheap ebay foil and actual decalpro fx foil, and no matter what I did I could not get the image to transfer to my surface in the last step. I was rubbing forever but it would not release from the carrier mylar. The only difference I had was that I dont have the decalpro fx paper, I was using cheap ebay waterslide paper (which of course came away as you'd expect in the water - just like your video). Any help would be so appreciated.

It is a great and affordable bit of kit. I have the PAW classic but with an upgraded Raspberry PI. Good video

Fantastic views, I must try out one of those 360 cameras. Thanks for sharing your trip.

Put suppression on the coax

That was a very nice long trip John. Good record of your destinations. How many of you went?

Wow, that’s a long way away. I remember you followed a shadow into a strip called 40 acre once, I noticed your panel was made up of 2 iPads. What apps are you using? Thinking of mounting a spare iPhone in one of the shadows.

Wonderful job!! :] I have a few question to you. Can I use any laser print water slide decal papers? And when I used laminator, the gold foil transfer on the water slide paper. How can I fix? Or how can I succeed? Actually I want to transfer only letter and logo. Please teach me and I am sorry for my english skills.. :(

I get all the way through the procedure until I get to the point of transferring the image on my model. The image won't stick. It comes off on the mylar, not the model. You mentioned a solvent. What type of solvent are you using. I am frustrated, thank you, your answer would be appreciated. Thank you, Robert Brown.

I thank you very much. You have made sense of this procedure. I am applying logos on model trains. Thanks. Robert Brown.

Awesome. Thank for sharing your process.

Hi John, I have the Rosetta too. Only seems to pick up airliners. Will I be able to see all traffic once I'm airborne? Thanks

Better with a static camera

Great for small one color decals but I am doing large full color graphics does anyone have a supplier for the larger sheet of the blue paper in the kit? I cannot follow Frank Miller instructions they are incomplete or are contradicting.

I can get everything perfect up until basically the very last step - applying the graphic and removing the mylar carrier. No matter how exacting I follow the instructions, part of the graphic comes up with the mylar...every time. Very frustrating. I'll watch this this carefully, thanks for the upload.

May as well go to the printer .

Hi, this is and old video but do you have an email to contact you?

Hi John Are you still using iPads as your PFD and EMS.?

Hi John, Thanks for the video, Making a panel for an RV7 aircraft and noticed you were doing decals for a panel too. Could you tell me what paint you used over the top of your decals? Was it a matt finish? Was 2 pak 2k paint ore just a rattle can? I have a can of PlastiKote matt, but not sure if this be ok. It is going ontop of a two pack black painted panel.

there are a couple different activators for super glue ... what is the actual ingredient in the activator.. thanks, helps us blocks in the USA ...the brand does not matter.

Nicely edited John. Looked like a great camp away.

No I am in Canada

How is the Grand Rapids and iLevil working for you. That is what I am planning for my 750 CruZer pannel?

Great video but can you just clarify the solvent and contact adhesive you use for White. As I understand the solvent you use is Super Glue Activator - this is prior to bonding with the Mylar film. You then use a contact adhesive on the finished graphic (with a mask) prior to applying to the panel. What conatct adhesive do you use? I plan to try this system for the re-labelling of vintage Leak amplifiers which were always labelled with white silk screen...

Good installation work.

well, my Discovery works fine with the Garmin GNC255A

I know of one other person, Mark Langford who had issues with the mgl. But there are hundreds of others out there who are perfectly happy. It is hard to tell if there is a real quality issue just from 2 or 3 cases, especially considering all the possible installation issues. I don't know what to to do.

Sorry but having the camera fixed to your head made me feel sick so couldn't watch too much.

Hi John, Great video. After watching this a while ago I bought the system and also the same laminator as you use. I am finding it hard to find more of the KK2000 spray adhesive and wondered if you have any good sources to get this in the UK.

Hi john...is there a uk stockist for this and could you tell me about the printing process...laser or inkjet...type of paper

Hi John, What is the solvent you use with the white? I couldn't quite make out the audio. Thanks for the video - it's extremely helpful!

Is that laminator modified in any way, or a standard Peak Pro? Thanks.

Excellent airmanship John. Well done. Must admit for a second that you shadow on the runway was another aircraft!

Just found the answer to my own question! Awesome footage as my grandchildren would say!

Great scenery, stunning camera work. What camera are you using John? Was it a fly in or just a visit?

I'm sorry but just use a sharpie - the method is a bit too complex.

Update. My friend called today and was told the upgrade/update worked now so he bought one. He has sent it back as It doesn't work still. All that work and a new panel is scrap. Show me one that works with 8.33....as rare as hens teeth