วีดีโอ

Beat china Epilog!

If you aimed for paraliziam you achieved that but squarness not correct method

Hi, 1:15 - aren't A series meant to have a soft-start feature? Thanks

Excellent

this is informative. thx

I have this exact set up… I was using just fine and all of a sudden I stopped getting a strong blue flame. Just a floppy orange flame. Thought it was time for a new tank, but continued with a a floppy flame, I was told maybe my handle was bad and replaced it. Still doing the same… could a bad tip cause this? Thanks.

The best 'How to video' on the Epilog Fusion Pro we have been able to find. Thank You!

Thank you for these great videos!!

This video IS FANTASTIC!!!

You mentioned if you crash a tool etc. That you recommend re-tramming the vice. I would also suggest checking the alignment of the turret/quill.

Interesting but WD40??? I would rather use a proper lubricant.

Sorry you are instructing people totally the wrong way .. best not to misleed people who are new to machining😕😕

What a load of bullshit. You should have listened when you went to school.

No No No No No, totally wrong from start to finish. Plus, unless you wanted a chamfer you deburring/filing is also incorrect. I suggest you cease trying to teach beginners on a subject when you do not understand the basics yourself.

Realmente me parecio muy util y valioso tu contenido ,aprecio el gesto de tomarte el tiempo de realizar este tipo de videos. No tome importancia a los comentarios negativos solo es gente que no aporta nada y solo critica.Saludos apreciaria mas contenido de este tipo.

Super helpful

Hello Friend good vídeo

How many times can you hone the vise bottom before you need to be concerned about the it going out of Kurt's table-to-vise bed spec? Also, do you need to tighten your mounting hardware to a specific torque?

This guy is a clown. Not only is the part not anywhere near square. You've got the quill hanging out of the mill 6 inches down. Not to mention you didn't choke up on the endmill in the collet either so 100% you're going to get some tool deflection... NEXT!

Re. Centering the vice on the table. My boss had a long table Bridgeport and he kept a vice on one end and a rotary table on the other end so that they balanced. This had a number of advantages. You seldom had to realign the vice. You had less time spent changing from a rotary table application and a straight clamping application. The wear on the screw and nut was more evenly distributed.

I learned a lot thanks for sharing

What load of crap you call yourself a machinist need to go back and learn the right way not tell people the wrong way

Totally wrong way to square a part! You should've had the part a least half it's thickness above the vice jaws and ran the end mill around it traveling front & right and then traveling back & left clockwise (conventional milling). Then do the opposite traveling back & right and then traveling front & left clockwise (climb milling) to the finished dimensions After that deck the top surface, unclamp, flip it clockwise 180 degrees, re-clamp, rinse & repeat. Never take advice from someone wearing a clown hat...

a star is born stacks

Ends were not squared to the sides. The part is NOT square.

If you are teaching this as a lesson for students…….the procedure is flawed. You are trusting that two or more of the block faces are tue when you start. What is your reference surface??? Stavros

U Shute think we are all stupid.I bet that’s not square

That's not how to square a part

Once you stood the part on edge in the vise, what gaurantee was there that the bottom you are referencing from is square to the sides? Good way to create a parallelogram.

Bravo.......great.....now cover the rear plugs....usb...pin...cheers

Thank you !

Need your help i need drivers apilog mini 30w legend 12*18 thnx :)

I'm trying to learn how to use the software to print is annoying people just show it working but not how they got it all done

It is a very good video. I wish you tested the power supply for transient load response and monotonic ramp up when output is turned on

Beautifully

Thanks…. Very informative…

Good video. What kind of stone is that? What should I search for? Thanks.

great tutorial.. detailed explanation . thank you

Thank you, great video!

Where to download that DXF file?? Or wiil you provide link for that?

Nice it helps a lot thank you

hello comments section