วีดีโอ

I have a 223 in my 1959 Ranchero .. Sweet running little engine ....

Thanks for sharing!

Thanks for sharing!

You have some cool hot rods 👍

Get u some ear plugs Dude!!

Bad Ass HotRod. !!!

Houch, in order to remove the torque tube, remove the six bolts at the banjo, remove the one bolt holding the radius rods to the t-tube. Then, remove the snap ring on the front end of the drive shaft behind the spline. Slide out the speedo drive gear thrust washer and slid the torque tube off the drive shaft. There is a seal and a sleeve that is pressed in the T-tube still in there and a big needle bearing that will come out when you slide the T-tube forward. To remove that seal and sleeve, get a piece of wood 2''x2'' x7'foot or longer than the T-tube and round one end the same diameter as the seal. Slide the wooden "stick" into the T-tube at the banjo end and stand the T-tube up on end and "tap" the stick on the floor and the seal will be pushed out with the sleeve. Install new seal with the same sleeve. Also, that is a 1934 transmission mount you have there. Good luck!

Hey Houch, that rear end is not a 1939 rear end. That's a 1934 rear end. The one that I'm guessing came with the car when new. That one-piece u-joint coupling is 34. That shock attachment on the rear end is 34 and the radius rods are 34 That rear spring with the arch sweeping forward is 34. You got yourself a 1934 rear end. And almost all came with 4:11 gears.

Love a Mercury

Has it been lifted in the rear? 😮

I love elementalism. You are a champion.

wacky races

sweet

Leave some cool for the rest of us

... Very cool cars, garage, and collection of vintage auto accessories ... The bell & hose set up really took me back to sweet memories ... Nice touch ... Best regards ... ⛽ 😁 ...

There is a Guardian Angel for everyone you Know!!!

Very cool old 31👍🏻🇺🇲

That's cool

👍🇺🇸

Works for him, Good job

Is that a four cylinder?

Wow that's the real deal for sure.

👍Good stuff

Sounds and looks awesome

Sounds great

Yes sir. 🇺🇸Lookin good! Gotta have a get away!

👍Nice

I am working on my 31 Model A which is completely original, and the trunk itself has a small back plate with a hole for the pin to go through. This gives much more metal to support the trunk. Your trunk lid with that one worn-out hole is missing the flat metal plate with the hole for the pin.

Sounds like a P-51 mustang lol

I have that same hat! Love your hot rods

Raw Horsepower 💪🏿

I have been in plenty of slow and uncomfortable things, but that white one just looks cool. 😅

Is that a stolen Chevy Deluxe?

The only problem with those are you have to be 5' and weigh 100 lbs.

Can't wait to see it

What an awesome shop!

Man that sounds great!!

What transmission are you running? I have a model a roaster truck with the same exact mods hopped up, was just wondering if you’re running the stock model a transmission ?

😊

What gear you have in yours i got a63 f100 &, its to low im look to change my

Is that a 351?

Looks and sounds great! 👍👍

That is cool that would be really fun to drive that is so cool❤

That's awesome. If you ever get the itch to sell it. I'll sell something. Even blood. I love it.

Great shop door the garage looks amazing❤

Great looking garage better school❤👍🔥👌😎🇺🇲

You got some cool cars I really like the Dinger the old gas station garage when used to pull through the garage and you'd hear the Bell go off❤👍🎱🏆👌🔥

Can't wait to get my banger out on the road!

Nice......sounds good . Is that a Burns intake ?

Feel better about the sounds of my 79 Chevy sounds a lot like that to me inside the cab but sounds great outside the cab 😂