- 7
- 26 307
What's Next
United Kingdom
เข้าร่วมเมื่อ 18 พ.ย. 2011
Stuff
วีดีโอ
Joffre Tug Boat RC
มุมมอง 416ปีที่แล้ว
Joffre Tug Boat electrics running gear. Caldercraft 1:48 scale
Spektrum Dx6i Transmitter won't bind to Oversky mxl-rx62h v3 Receiver. Help!
มุมมอง 5693 ปีที่แล้ว
Spektrum Dx6i Transmitter won't bind to Oversky mxl-rx62h v3 Receiver. Help!
Do we have to cut the rubber out to find these screws?
@@connorwaghorn2187 The rubber gutter strip is glued on, but with some gentle persuasion you can slowly peel it back from each end to locate the screw positions, after 'neatly' drilling a hole through the rubber, press it back in position. NB: If you buy a new set of Ford roof bars they actually come with a kit of 6 pre cut replacement rubbers and 4 screw cover caps, so you don't have to go through all that faff.
Does this boat come in kit form?
Hello, You can get the boat in kit form from the following link www.hobbies.co.uk/model-boats/model-boat-display-kits?adid=&matchtype=&
If you bought the XML-62H-A I believe that works with the Flysky transmitter. For the Spektrum transmitter you need to buy a XML-62H-D. When binding, make shure the transmitter and receiver are 3m apart.
Thanks I ended up getting the SuperMicro RC Rx62H V3 DSM2/X Rx/ESC/Servo board from Stevewebb model's.
Where can i buy this model
www.hobbies.co.uk/caldercraft-joffre-tyne-tug?adid=&addisttype=xpla&matchtype=&gclid=CjwKCAiAheacBhB8EiwAItVO2xPZKgKThXbGA3dSdxu890vOLCe1yGso6pNQV-YnG5uMpH_KeL5loBoCxkAQAvD_BwE
Viene asi originalmente o agujereaste el techo?
You are to close to the receiver. I had the same problem and need to just move about 10 feet away then it worked.
This really helped me, thanks!
So how do we get the rounded plastic screws out lol
did u manage it to get work ???
Unfortunately no joy at the moment, I need to try it with someone else's transmitter that will rule out if its the transmitter or the unit.
Ive now Tried a later spectrum transmitter and it would also failed to blind. This was from banggood and arrived in a non padded plastic bag so not really surprised it's faulty.. I'll be ordering another one but from UK supplier this time.
@@mikecalver1 try lemonrx I asked them and they told me their bricks work with all soektrums A bit more expensive but still not like spektrum prices
I have just ordered this roof bar kit for my MK7, however I have heard a few people say that they leak, and let water into the interior, have you had this problem?
No leaks on mine.
@@mikecalver1 I’ve had mine on for a couple months, all good 👍
I cannot find the holes? Mine is a 2014 st 3door.
Best to check with Ford dealership as they may be located differently on a 3 door Fiesta.
mine is a 3 door 2012 version and after removing trim moudable rubber bars, holes are there and covered in a rubberish material.. its easily spoted by eye because its an irregual surface zone, and with a knife you can remove that bolt protection..
@@ssergi0 I've done this today... absolute pain of a job!! why use plastic screws???
@@chazteb ahahah, true! my first screw i remember it came out damaged as hell. The next ones were a bit easier. Did you fit the bars? Mine were original ford rack bars i found online, i spent like 2h to get it done
@@ssergi0 yep, did them today, those screws are a nightmare, they look sick on the roof though!
Any idea of the measurements to locate these holes please?
31cm from the front edge of the roof and 51 from the rear edge of the roof. For mine. You can peel back the plastic gutter strip, mark the hole to drill then stick it back down. Should look pretty neat.
What year model you have and how the roof trim was installed, tape, glue or something?
Hi Michael, under the strip is like a plastic gromet do you drill that out? Or screw it out