วีดีโอ

❤️❤️❤️

❤️❤️

❤️❤️❤️❤️

❤️

😍⚘️

Thanks

⚘️

❤️thanks

I don't have the right tools, the right lighting, and the right camera No one supported me to improve and make better videos

@@SP_ELECTRON1384 Hey, why you be upset?? If content is better, so no quality matters. Okay? There is no way to be upset. Can we be friends? I will help you to make your channel ranked. I will help you as your friend. Let's make a chat privately. What you say?

Hello, dear friend, it is recommended to use 100k. it is better

One more question my friend, if I use RC driver available in the market, is it shock proof? You never showed, how to find out Zener diode value. Please reply.

My friend, it is better to use the same 1n4444 diode, it does not cause any danger, and you can also use the RC driver, and this video is just a cheap idea.

💖

💖💖

💖💖💖

😂😂

Hi dear friend Great, there are many ways to make a solar panel, this is one of them⚘️

No, bro..😁

I don't think 5v

I didn't have a multimeter to measure the voltage, but I had a homemade voltmeter that read 3.2 to 5.3.

What is the current

this is not fake this is a shit trush

We are glad you enjoyed our video..⚘️😊

Hello dear viewer You're right, but when you lower the voltage, no power is consumed, the battery lasts forever.⚘️⚘️

@@SP_ELECTRON1384that’s not how it works 🤦‍♀️ the light still consumes power just less but what about when you need it on full brightness? It’s better to make it have lithium polymer batteries and a BMS attached to them and a board from a usb phone charger that connects directly to the screw where the lightbulb would get power from while being operated normally so to charge, just screw it into a lamp

Nice vid btw

@@pgee7777 Hi dear friend this is just a cheap idea I will make more interesting ideas soon

@@SP_ELECTRON1384 okay

Hello, thank you very much for your beautiful and motivating comment. With your support I will definitely continue....⚘️

🌹🌹

Brother, I made 2 models of these devices and they are still working and I am still alive

​@@SP_ELECTRON1384it's a poor and shitty abd dangerous design

Yes, you are right, but this idea is good for those who like to make LED tester very fast and very cheap.

Yes, that's right, I did, now I'm dead😂♥️

No, there is no very serious danger, the electrocution is very weak

Yes, it is true, but this is only a cheap idea

people with way less knowledge will try building this. just saying it is not safe

Bro, this is just a cheap idea for those who want to quickly build an LED tester Otherwise, I will make more secure versions later

​@@SP_ELECTRON1384Bro, stop using mains voltage if you don't no know electronics

Hello, dear friend, electrocution is very weak and not fatal

​@@SP_ELECTRON1384it is absolutely fatal when your resistor fails

The risk is very low and it is not sensitive even to short circuit

Hi dear friend The output voltage is variable

♥️♥️♥️

Thank you🌹🌹🌹🌹 Please support us🔆♥️

Hello, dear friend, this device is a very weak electric shock, it is not very dangerous, I tried it myself, it was weak I'm still alive🖐😂🖐 🌹

Relying on two small 10k resistors connected to a bridge rectifier is not safe. You may be ok, but others dabbling in such risky electronics may not be fortunate.

Hello dear friend, your explanation was very brief and useful But remember that this idea is cheap and you won't find it anywhere easier We tested with this LED light device many times but it never got hot And if two poles are connected, nothing special happens And it's not very dangerous, electrocution is very mild

Yes, it's cheap and easy. But is that a greater advantage than endangering human life and possibility of destroying the parts being tested? You are probably working with an isolated 115V mains (common in the USA for example). Here in Europe we have 230V and phase and zero (zero is grounded and there is always a life-threatening voltage against ground on phase). You have to take into account that your idea can be copied by anyone all over the globe and it is not always as safe as you believe. I also test boards for LED bulbs, but for that purpose I got a low power DC-DC Boost Converter 8-32V to 45-390V High Voltage at Ali and I have a 300 kohm resistor at the output, current about 1 mA (that's enough, otherwise the LEDs shine too intensely in my eyes). It's safe and cheap (about $4 including shipping).@@SP_ELECTRON1384

@lubomirwinter2628 You have very good information, thank you very much 👏🏻👏🏻 But we live in Iran and the voltage here is 230 volts And we got a good response from this device in every way And there is no danger for you dear followers🌹 This device is capable of giving 124 volts DC! And when testing LEDs, its voltage changes

​@@SP_ELECTRON1384 I work in the industry and therefore have to know the safety standards (and prove this knowledge regularly before a professional committee). The conductor I can touch has a permitted AC voltage of 25V and a permitted AC current of 3.5 mA (through the human body). This is not the case with your device. Yes, due to the bridge rectification effect, both output conductors show about 120V to ground. And both are equally dangerous to touch! Sure, when testing an LED, almost the same current always flows and the voltage is reduced due to the resistors involved. It works on the principle of a current source.

Kudos to you and your level of alertness May God protect you👏🏻👏🏻🤜🏻🤛🏻🌹

Hello, dear friend, yes, I agree with you, this device is not safe because I got electricity with this device, but this is the simplest and cheapest idea that I taught you, and I will teach you professional ideas later.👋🏻🌹

Hello, thank you very much, the problem is that the industrial alcohol has run out. And it was not tested💔

🤣🤣🤣🤏👏🏻⚘️

😂😂😂💗

💗💗💗💗🙏🏻

😍😍😍😍💗💗💗💗💗

⚘️⚘️⚘️⚘️⚘️

💗💗💗💗🐶thanks for watching the video

🙏🏻🙏🏻🙏🏻⚘️