วีดีโอ

Jim, Did the gun heat up at all? I’ve heard they get hot, may have been nonsense.

I must admit you are pretty good when you get started on something. When you went to reloading you have gone all in. I have never seen anyone advance as quickly as you have. I have a Dillon 550 and went with it because it was dependable and had a great tool head set up etc. Never really trusted the progressives that advance themselves with a pull of the handle. I don't shoot large numbers of rounds as you do but I reload a lot of calibers and love a tool head set up. So, what I have works for me. I am glad that you are doing so well and seem to have got educated enough that you most likely are doing better with answers than a lot of the advice you get. Keep up the good work. Nice video.

I like both those presses. I do have the Co-Ax at my farm and will be getting the F-1 as well to do the things the Co-Ax does not do as well. I am working loads at my farm. I have presses at the house too more capable of loading bulk numbers of rounds better like my Dillon 550 and a Lyman turret press with 8 stations. I would suggest either of those two for doing your pistol loads if you shoot lots of rounds. Save a lot of time. The Dillon 550 is pricey but it's the cat's meow. The turret press will just get you to the next process with the turn of the handle. I use my Dillon 550 for when I load a lot of rounds in either pistol or rifle. I use my turret press for bullet pulling, removing primers or small reloading jobs for something that is not set up on my Dillon 550. I did like your video and see that you are certainly a serious shooter. I have reloaded for over 40 years and have upgraded equipment for years and still do. Frankfort Arsenal makes a lot of good products. The presses and wet tumblers are hard to beat. I have even tried their universal bullet seater. It does work as advertised but with a bullet seater often the piece that seats the bullet has to have the proper fit to the bullet to seat consistently. And I found that when I used it that it did not work as well as some other seaters that I had that came with the dies. Anyhow, thanks for your video.

What powder check are you using?

Just did this last week. Went to zero it with my 14 yrold, kinda panicked a bit with the first shots. Forgot that with both rifle and scope level, the point of impact is way low until you make adjustments. Felt kinda dumb for a minute, and then within 20 minutes, we were driving tacks at 60 yards. So much fun experiment ing with different ammo. Great day with perma smiles. Thanks for the video.

Amazing Pistol‼️ Silver PVD is available now 🔥

Can anybody help me find the water soluble lanolin I can’t find it at Amazon.

I had that same problem treid to punch out the bearing and cracked the arm all started because primers jam and primers jam because of the bent priming rod they give you clips the gear on the priming system flips primers over there is more videos coming out with the same problem looks like FA have quality control issues.

Great video Jim

Thanks for the video, and maybe the grit had a _tiny_ bit to do with the appearance, but no man, sorry, has nothing to do with the dirt and everything about leaving it in an acidic solution for too long. Now take all that brass and put it in a dry tumbler with corn cob media and some Dillon Rapid Polish or Nu-finish and it will come right back and be almost as bright as your other previous batches. My formula is 2 tbsp of Armor all Wash & Wax with 1/4 tsp of Lemi-shine and I did the exact same thing, left it sitting for over four hours after a 90 minute tumble, and it looked almost as rough as yours. The dirt and sand and grit had nothing to do with it. From that point on I never tumble longer than 75-90 minutes and have never had an issue. For really filthy range brass I tumble only in the wash & wax and no pins for 30 minutes to get the worse of it off, so I don’t have all that grit and dirt in my machine then dry then decap. Then run it for 90 minutes with Wash & Wax, lemi-shine and pins, comes out perfect. Test this yourself: tumble a batch of pristine clean brass in clean water and that brass juice stuff (I think you’re wasting $ there but your call) and leave it in overnight again, and the brass will have the zinc attacked by the acidity and look just as bad as the stuff you’re showing. That attack to the brass will make it feel like steel. Another reason I like the Armor All is the brass has a lot of slick lubricity after because of the wax residue. Nice Desert Eagle by the way! 👍

Ar

Dang I missed it!!

I just bought my reloader off amazon. It will get here next week. I thanks you both for taking me on your journey. I'm also a youtuber and I will be putting both links on my page when I do my unboxing. God bless and stay safe...

What you have shown is how you adjusted the dies?

Nice!

I'm having problems with priming. Inconsistent priming depth, I keep adjusting primer rod. Seems to be right on, and after a few some, still not flush. Sometimes, it makes a snaping noise. I'm not sure what to do. Have you had any problems?

Thousands upon thousands of rounds that way...never an issue. Ando for those that will comment that it screws with the powder...that would be wrong as well...many many many chronograph tests prove it.

You amateur TH-camrs need to learn to stop saying UM all the dam time. Its annoying and reduces the watch-ability of the video

amnt head stamp for 223 rem. has off set flash holes which have broken my decapping pin! who makes this brass?

Thank you for turning your issue into a teachable moment

Thanks for keeping it real...

The Hornady lock'n'load bushings fit for easy caliber changes.

Great video, looks like an awesome product!

*Starring 😉

Congrats @tommytaylor7851!

Have you tried or considered making a shorter handle to reduce how low it goes on the down stroke? From what I’m seeing this press is smooth and takes little effort so it should lend itself to a shorter handle?

Great job old fart! 😂😅 Congrats Tommy

Congratulations to the winner and great video

Congrats to @tommytaylor7851 and thanks Jim.

I won …… I’ll be in touch Jim… Thanks for

Ohhhhhhyeeeaaaaah baby let's get this party started 🎉🎊💪😎

Right on brother!

Boom !!!!

Alright Jim!

Way to go!!!!

I was off by 2 days.

Hit me up for the coyote hunting, I'm in with ya!

I'm ready to take the journey with you guys! Let's go!

Great watching you grow!

Ohhhhhhyeeeaaaaah baby let's get this done 📶 ✌️

Lets Go

Well send you an 06 sizing die guys.

Thank you for the effort and appreciate the work you and son put into this keep the info flowing 💪

Day 16 2.1 miles

Look forward to it. I have enjoyed your reloading videos.

Day seventeen is going to be the day💪😎

I feel it day seventeen 💪

You saw and got a wabbits. 😮

Well dang!

Make me right tomorrow Jim.