วีดีโอ

You need to oil your frame before it rots out lol

I was trying this on my son’s 2008 focus and push the button and nothing happens except check engine light blinks , car ran normal b4

Anyone have a link to the part

Is that a 351 Cleveland

Very helpful for replacing my starter. My truck is a 2005 Sport Trac, so it was easier for me to crawl under the front of the truck versus the wheel well. Thanks again.

Why splice. Just back feed into the backside of the wiring.

Any before and after pics, mine sags bad

I took my tire down. I could sit under truck.

Did my 06 Duramax today. The bolts were a nightmare. Last 5 took 3 hours. Nothing to grab on to. Corroded heads. Put new cover on and new bolts. 6 hours. Looks good and no leaks.

Got a f725 and 265. ❤ them

Watch out using brake clean with chlorine in it. If it burns it makes poison gas, strong and deadly. Still using your JD? I'm looking around to find out how to raise the seat, mine seems to be stuck. Have to remove the deck because the gearbox is locked up, need one of those too.

I feel you man especially about the kids and the tools except for my chickens being out it's just pissing rain freezing rain on me

America!!

Thanks for your video

Where does this O2 sensor plug in at because 03 Malibu given to me with no O2 sensor or catalytic converter and I got to find out where it plus onto

Great content, thanks for posting.

PB Blaster or WD40 them rusted bolts 10 mins before you start, and it should be a tremendous help!!!

People love to bash Ford.Id say the original starter lasting 175K is alright.

Is there a rear seal and pump gasket that need to be replaced too?

I did a more ghetto fix on an old VW golf, just had 2 wires hanging from my steering column that I pressed together to start it. I have an 08 focus with a failing ignition switch right now, but instead of a push button hanging from the dash I got a new ignition switch from rockauto for $24 shipped. Might have been a few bucks more than yours, but I can't complain too much about that.

You're 💯% right. The parts store clowns are absolutely the worst. Every negative stereotype there is... sure seems to be true. People don't try or have pride anymore.

Nice! You could pull the bearing and seal out at the same time using the bearing puller.

This is amazing man!!!!! Taking mine apart right now and had not seen a video like this which was incredibly helpful! I felt all alone but now I am ready to get back at it tomorrow!! You the best!!

You're so gifted.

I had a torque converter go bad and it destroyed that seal but also a metal ring/sleeve came out too. Any idea what it would be? Its on the torque converter shaft that goes into the trans

Where is the h02 sensor located on this model car.

4:25 This is the moment I hoped for and needed to see. It CAN come out the wheel well. Still gonna have to crawl around in the gravel on a cardboard box (aka broke peoples creeper) but at least I don't have to drop it on my face when it comes free.

Definitely helped here.

ou have to control your lenguage when you make videos or not maket at all . and you right the video is sucks

if it ain't a mack ! You might as well take it back 💪

I would have put thoes races in the freezer for a bit

I don’t know if it’s coincidence or trailer companies trying to screw consumers but I have always done my bearing’s similar to you but the last new trailers I purchased the inside of the race sat flush with the inside of the hub making it impossible to pound out.

Pongan lo en español

Can’t get those damn top bolts..

Just use the spring compressor and don't remove any of that stuff...

Great instruction … thanks for doing this, you’d be an honest mechanic.

How do you get the wire into the blue small things?

Did this stop your leak? I have the same issue but the transmission shop said you’re also supposed to replace the transmission pump bushing or it will leak again soon or right away

👍🏽

What about if you do not have the key ? How you would start the car ?

Where you order coil spring

Hey, I just had a quick question if you would, please answer it because I don’t know nothing about motors or none of that I do woodworking and it is beyond me when it comes to mowers and stuff. Hi see that there’s some type of green liquid in that plastic area you have right there in that little plastic on the side. What goes in there cause mines bone dry I bought mine at the auction and it’s bone dry I just wanted to make sure I was putting the right fluid in it is that coolant or is that transmission fluid?

You DA MAN!

Made me motion sick watching this

mine sags over bumps replaced the shocks and does the same i already have the new trailing arms to replace them do you recomend changing the springs also

Finally a solution for this struggle, i've tried with the tape method but this is better, thank you

Great video and way to go with having your kid there with helping you out. He not inside playing video games and will know how to work in his own stuff one day.

Thanks for making the vid, just found a ton of play in my wheel in the parking lot of auto zone and need to do this, you make it look simple!

How can your viewers gift you a tripod and what type of tripod do you need?

How can your viewers gift you a GoPro?