- 16
- 134 056
Wight Water Pools
เข้าร่วมเมื่อ 30 ส.ค. 2010
WWW.WIGHTWATERPOOLS.COM
Review of Polaris Atlas Suction Pool Cleaner
A quick review of the Polaris Atlas suction pool cleaner.
มุมมอง: 983
วีดีโอ
Introduction to Wight Water Pools
มุมมอง 1119 หลายเดือนก่อน
Introduction for Wight Water Pools Service and Repair. Serving Madera, Fresno, Clovis, and nearby areas. Facebook: Maderapoolservice/ Instagram: waterwight Website: wightwaterpools.com/
How to adjust your pool autofill valve
มุมมอง 21K2 ปีที่แล้ว
Wight Water Pools, adjust and install a swimming pool autofill valve. These valves replace old brass style valves. pool service and repair in Fresno, Clovis, and Madera. Pool maintenance
How to install a pool weir gate
มุมมอง 4K2 ปีที่แล้ว
Wight Water Pools, Installing a weir gate into a pool skimmer. What is a weir gate? Why do I need a weir gate? What is the flapper in my pool skimmer?
How to operate a yellow dial timer for your pool pump
มุมมอง 3342 ปีที่แล้ว
Wight Water Pools, operation of a yellow dial timer for pool pump and booster pump.
How to operate your Pentair Ultratemp pool heat pump
มุมมอง 16K2 ปีที่แล้ว
Pentair Ultratemp heat pump installation. Why purchase a heat pump over gas heater for your pool. Pentair pool heater operation.
Why you want to adjust PH in a pool. Causes of Low pH
มุมมอง 577 ปีที่แล้ว
Low Ph, High PH, Wight Water Pools, Fresno CA, pool service, Madera pool care
Wight Water Pools Fresno CA
มุมมอง 6469 ปีที่แล้ว
Setting Easy touch Schedules and egg timer. What's a egg timer?
Pentair Screenlogic
มุมมอง 82K9 ปีที่แล้ว
Pentair, easytouch, screen logic, screenlogic, easytouch light, controller, pool, fresno pool, madera pool, la pool, san fransico pool, hook up screen, download screenlogoic, pentair intelli
Wight Water Pool Service KMPH Interview
มุมมอง 63714 ปีที่แล้ว
Help with questions on pool service and Repair. Fresno pool service questions. Pool maintenance details and pool cleaning details.
This video sucks
lol - nice video. no ending.
The condendser is to close to the wall
Pool liner guy replace mine years ago. Been sticking closed ever since. Help!!
Pool out and blow lines and replace. Adjust and make sure it goes up and down with fingers.
My pool heater is the same. When i press the on/off system wich is actually « running ». I mean i see the screen is lighted but the pump never start even if its written to allow 5minutes for the system to start. Someone knows something about this ? Thank you
Someone may have set up a delay. Call Pentair
@@POOLSERVICE an electrician just pass by to fix my electric box and tested my heat pump. A relay Seems to be defectuous.
What would the service light come on ?
Thank you! Yours was so easy to understand! Thanks
Do the spring loaded pins go into holes?
No. You hold it in until its against the wall, then release the end so it pops out against the wall and holds it in place.
What level should the pump be when turning on the heater?
Would you rather have the screen logic to control your pool with your phone or is it better to have a control
screen logic
TX led on ScreenLogic wireless interface wireless link inside the house is blinking amber, cannot connect anymore. any ideas?
Super helpful! Thank you so much!
Great video but the troublesome wireless part is not needed when you can use a $20 wireless network adapter and achieve the same thing. Here's a video of how to do that... th-cam.com/video/8o74R0HZ3nw/w-d-xo.html
????
@@Think-dont-believe Here you go th-cam.com/video/8o74R0HZ3nw/w-d-xo.html
Swimming in the Deep THANK YOU!!!
THANK YOU FOR YOUR HELP. I ALREADY INSTALLED THE SCREENLOGIC, ANY VIDEOS ON HOW TO USE THE REMOTE ACCESS ON THE SCREENLOGIC?
Nice video! I created this over a decade ago. Watch for the new ScreenLogic iOS app - it's awesome!
You created the screenlogic protocol adapter? Cool.
Worked perfectly for me. Don't forget to use the correct case and spacing when putting in username an password. Thanks for the video!
Thanks for the positive reply!
can you change pump schedules and stuff like that through the screen logic? or do I need to go to the easytouch panel for that?
Just tried this and the instructions on the user name and password are incorrect. In the video when the remote connection isn't working he switches to local connection so no login is needed. The user name should be "Pentair: XX-XX-XX" with all of the letters in the address uppercase and first letter of Pentair uppercase. And a space after the colon. The password should be blank by default. You could probably get into a lot of peoples systems by bruit force guessing. To change your password from your iPhone or iPad download ScreenLogic Config and go to General Settings -> System Info & Password and set a new password there.
You really need to take your Protocol adapter address out of this video. It just tried to connect for giggles and got to your equipment with no password.
Eric Phillips I don't believe that. Because if a password is set not using one even with the name on his will not get you to his equipment
use Ethernet cable to plug into screenlogic interface
how do you pair the wireless link to your internet?
Just select the same wireless internet you plugged ethernet cable from screenlogic system.
Connect it to your router or access point