- 98
- 25 593
Redneck Entrepreneur
United States
เข้าร่วมเมื่อ 24 ธ.ค. 2020
Fabrication, modification , welder, knife maker and general Redneckery
Project truck f550
Minimal mods to sell a truck as a project truck for the purchaser.
#automobile #weldeverydamnday #dailygrind #mechanic #welding
#automobile #weldeverydamnday #dailygrind #mechanic #welding
มุมมอง: 19
วีดีโอ
Boss snow plow on Suzuki Kai truck
มุมมอง 399 ชั่วโมงที่ผ่านมา
One off install of a boss atv plow on a Suzuki Kai truck. #automobile #weldeverydamnday #dailygrind #mechanic #snowremoval #welding
V10 for hydro swap
มุมมอง 169วันที่ผ่านมา
Swapped out from central hydraulics to electric over. This year v10 ford doesn’t allow mobile pto and they needed mobile. So swapped out to the easiest option. #automobile #weldeverydamnday #dailygrind #welding #mechanic #hydraulic
Rust repair on 2013 f350
มุมมอง 3514 วันที่ผ่านมา
Small rust hole repair in a 2013 ford f350 work truck. #automobile #dailygrind #welding #mechanic #weldeverydamnday
Fitting an old crusher to a komatsu 350
มุมมอง 61514 วันที่ผ่านมา
Dug an old crusher out of the weeds and fit to a komatsu 350 excavator. #welding #dailygrind #mechanic #mechanist #heavyequipment
Easy fender swap after smashed.
มุมมอง 1221 วันที่ผ่านมา
Customer smashed fender and ripped it off. Easy peasy replacement. And rewire. #fabrication #dailygrind #welding #automobile #customfabrication
Snow chute for very large snow blower part 3
มุมมอง 21หลายเดือนก่อน
Finishing up the chute lift kit and tilt hydraulics. #fabrication #automobile #snowshovel #snowblower #welding #snowremoval #dailygrind #mechanic
Snow chute for very large snow blower part 2
มุมมอง 28หลายเดือนก่อน
Proceeding with the fabrication of the snow chute lift kit. #fabrication #welder #dailygrind #snowremoval #welding #customfabrication
Snow chute for very large snow blower part 1
มุมมอง 240หลายเดือนก่อน
Very large snow blower didn’t quite have enough height to shoot over a Triaxle bed. Gave a lift kit on the chute. #fabrication #welder #welding #snowremoval #customfabrication
Garbage truck repair (daily mundane bull)
มุมมอง 138หลายเดือนก่อน
Repaired the rear latches that were bend all up. #fabrication #automobile #rusty #welding #dailygrind #welder
Skid steer broom replacement.
มุมมอง 222 หลายเดือนก่อน
Replaced the broom wafers on a skid steer broom. #fabrication #welder #welding #dailygrind #machining #snowremoval
Kubota broom replacement.
มุมมอง 533 หลายเดือนก่อน
Kubota broom getting a bit worn so pulled it off and replaced it. #dailygrind #fabrication #welder #snowremoval #kubota #kubotatractor
Boss plow repair
มุมมอง 563 หลายเดือนก่อน
I had built a small adapted utv vee plow onto a sac skid steer. Well the guys managed to destroy it. So here is the repair. #fabrication #welder #welding #boss #snowplow
New bucket
มุมมอง 343 หลายเดือนก่อน
New case 580 (to us) salt how needed the correct size bucket for a measured ton of salt. Fabricated new bucket and installed. #fabrication #welder #welding #rustrepair #case
Hood hinge repair on Peterbuilt.
มุมมอง 344 หลายเดือนก่อน
Good hinges were worn out, made new bushings and replaced/made some hardware. #welder #fabrication #welding #peterbuilt #machining
Hinge replacement on an aluminium bed.
มุมมอง 474 หลายเดือนก่อน
Hinge replacement on an aluminium bed.
Awesome 😊
I go throw suspenders like ever 2 months I need me so
Let me ask him if he’s still willing to share his info and I’ll pm you
@@redneckentrepreneur212 thanks
Also, did straight from battery the top of the plug
Did it many times straight from the battery right into the top of the distributor?
good job
Thank you!
Awesome 👏
Thank you!
I sent you a message on your Facebook account. It's a request if you don't mind.
Awsome
Thank you.
Nice job
Thank you!
Great work! I am rebuilding a 47 plymouth coupe
Awesome! And thank you.
😮. Awesome 👏
Thank you kind sir.
Where's your eye protection ???
I assume you are referring to welding? Because I am overly crazy about safety glasses, but for welding I am good. Just shield my eyes and tack away. lol.
Did you weld the supports on? Are they plug welds or just stitched? I am loking to do this on my truck in the next few months.
Sweet. Yes they are spot welded.
@RedneckEntrepreneur Wow!!!!!! I am inspired by your awesome professional detailed super GOOD work!!!!! I got my 50' body off on some A Frame jacks... I am trying to clean up underneath... it would be sooo much more easier with a rotisserie holder... I have the car at my Dad mechanic shop... He can weld some but I wish I could get good at welding as well... and do it like you too ✌😇🙏
Thank you so much for the nice words. Just keep at it my friend. Welding is just practice and time under the hood. You’ve got this! Sounds like an awesome build.
@@redneckentrepreneur212 Thank you Brother in the old classic car hard workers crew ✌😇🔧🔩🧰
Great stuff here......and courageous (and quality), work to repair this neat old car. I have a 48 Plymouth 2 door sedan, purchased back in the mid 90's. It was a complete car and running, but not road worthy, but amazingly rust free for a 40's vintage car in the north east of Canada. The car must not have ever been driven in winter. Only a couple rust spots at the lower back of the rear fenders, as usual for these cars. I'm not a mechanic but was very fortunate to find an older man in 2010 who was specialized in these older models of Plymouth's and had worked on many. He did a two and a half year rebuild of the car, not a body off restoration as that was not necessary, but everything striped out otherwise. Had the interior done to original specs by a specialist and the only thing I was able to do was the wood graining for the dash and window garnishes and other small details. The repaint was done base coat - clear coat in Caribbean blue (very close to an original Ply colour. All chrome replated and stainless smoothed and polished, Cocker white wall radials (bias look-alikes) and the car still runs and looks great after 12+ years since the restoration.
That is amazing! Thank you for sharing. I always love to hear about classics that are treated right. And I love the two doors.
Would you happen to know the part # or name of those rear supports that you said were on back order ? Tried looking them up and no luck
I do not. Parts was sourcing all that. Sorry.
How did you wire this bed up I just put one on my truck and can’t seem to find a harness
So to be perfectly honest I 100% don’t remember. Pretty sure the 2010 was old enough I could go off the trailer harness without popping a code like the new ones. The newer ones you either have to tap into the light harness or get an adapter harness like from duramag. The older ones you can tap the trailer wiring and not get the “trailer connected” code.
Awesome I appreciate it a lot I will look into those options I’m working with a 12
Awesome I appreciate it a lot I will look into those options I’m working with a 12
Awesome. Hope it helps. Let me know please. Or don’t hesitate to holler if there are challenges.
Non ya lol
You are the first person to catch that! 🤣
Very nice
Thank you. ☺️
😊
😊
Nice work
Thank you!
Very nice work. Happy new year
Thank you sir! And happy new year to you! 🎉
Merry Christmas
Thank you! Merry Christmas to you too brother. And happy new year!
Did you use the OEM tail light harness to wire them up?
Sort of. Factory to the back, I added a weather pack connector and new bed harness from there. So it’s only factory to just behind the spare.
I want a bucket now
Send me dimensions and I’ll whip ya one up!
@@redneckentrepreneur212 bucket work free....... Shipping $500387.99 .... I'll wait until you move over here lol
Could you find a louder stool 😂
Don’t challenge me unless you are ready for the outcome! 🤣
i like watching the process of your work . I have a 1941 spa.delux 4dr . I will be the caregiver of it my father pass on and left for me .Thanks for the videos , and i'll be back !
Awesome. Thank you!
Farmerized!!
Are you transphobic? Ba wa hahaha
Anti mechanic is a perfect description lol
Right?! 🤣
Bro that smily face lol. Great work!!!
😃
It’s coming along nicely so far.
Thank you kind sir. ❤️
Awesome
Thank you!
Doing my first set now for a customer how long did it take you?
It wasn’t too bad. All in like six to eight hours. I don’t remember exactly.
Cut scenes is your forte bro
Thanks bro.
Wowers that's definitely very crazy. Very nice job.
It was a different and fun repair.
Wow, just wow😮😮😮
Very nice job. Can't wait to see more updates an projects and many more videos soon my friend. Keep up the great craftsmanship and hard work my friend. Fab On. Weld On. Keep Making. God bless.
You are so kind. Thank you so much. God bless you as well my friend.
Make a dry cell using graphite sheets, much safer. Also with a flash arrester to prevent that
bummer thanks for sharing.
Use sch 40 PVC. Should stay in one piece even if boom. Nice thing you can do also is machine a nice pop off cap, that's also a quick fill up cap, that's assuming you don't build pressure inside it. ( not recommanded anyway. ) 6 cells is a good design, cause it's the only way to avoid current leaks ( drycell do leak, current and fluids )
I almost did use pvc, but there was a very specific point to my budget and it didn’t fit. The follow up build will be the no holds barred, highest mileage gain, no budget build. lol. And you can guarantee I will be putting a blowoff in. lol
I blew up a very expensive K&N air filter in a dodge once. The gas built up for some unknown reason and eventually just blew inside the intake. it shredded the top of the filter and really made a nice boom. I think it was a little cool that morning and I should have waited until I got her warmed up and moving before I put it on. I had a bubbler and an external unit that was never harmed but it basically made a bomb out of my intake. LOL
Awesome! Not really but totally awesome. 🤣
Can't wait to see more updates an projects and many more videos soon my friend. Keep up the great craftsmanship and hard work my friend. Fab On. Weld On. Keep Making. God bless.
I'll be waiting for the update vid brah
Thats my little brother, what great work!!!
Awe! Thank you!
Nice job where did the rails come from...
Parts sourced em. I asked him yesterday and he wasn’t sure. Bossman said partsgeek maybe. (The parts guy quit since then lol)
@@redneckentrepreneur212 thanks I found them at Dorman 419.00 now to define someone willing to do it
Where did you get your rails? Nice job....
I am not sure. Parts got them for me. Let me check tomorrow and get back to you
And thank you!
@@redneckentrepreneur212thank you so much
So the parts guy that got em has quit, and the bossman isn’t sure where he got em. He thinks partsgeek. Just do a google search and look for the best price.
@@redneckentrepreneur212 thank you
Very nice work. Nice repair. Can’t wait to see more updates and projects an many more videos to come soon. Keep up the great craftsmanship And hard work my friend. Fab On. Weld On. Keep Making. God bless.
You are so kind sir. Thank you so much. God bless you as well!
Millimeter???? Are you British??😮😂
I was out of eagle feathers to measure in freedom units. 😆